background image

Page 18

SKU 97743

For technical questions, please call 1-800-444-3353.

liMiTEd 90 dAY WARRAnTY

Harbor Freight Tools Co. makes every effort to assure that its products meet high 

quality and durability standards, and warrants to the original purchaser that this product 

is free from defects in materials and workmanship for the period of 90 days from the date 

of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, 

abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, 

improper installation, normal wear and tear, or to lack of maintenance. We shall in no event 

be liable for death, injuries to persons or property, or for incidental, contingent, special 

or consequential damages arising from the use of our product. Some states do not allow 

the exclusion or limitation of incidental or consequential damages, so the above limitation 

of exclusion may not apply to you.

 THIS WARRANTy IS ExPRESSLy IN LIEU Of ALL 

OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDINg THE WARRANTIES Of 

MERCHANTABILITy AND fITNESS.

To take advantage of this warranty, the product or part must be returned to us with 

transportation charges prepaid. Proof of purchase date and an explanation of the complaint 

must  accompany  the  merchandise.  If  our  inspection  verifies  the  defect,  we  will  either 

repair or replace the product at our election or we may elect to refund the purchase price 

if we cannot readily and quickly provide you with a replacement. We will return repaired 

products at our expense, but if we determine there is no defect, or that the defect resulted 

from causes not within the scope of our warranty, then you must bear the cost of returning 

the product.

This warranty gives you specific legal rights and you may also have other rights which 

vary from state to state.

3491 Mission Oaks Blvd.  •  PO Box 6009  •  Camarillo, CA 93011  •  (800) 444-3353

Record product’s Serial number Here: 
note:

  If product has no serial number, record month and year of purchase instead.

note:

  Some parts are listed and shown for illustration purposes only, and are not 

available individually as replacement parts.

Summary of Contents for 97743



















Reviews: