Chicago Pneumatic 6151939534, Operator'S Manual

CP9534, CP9674

6” Random Orbital Sander

Original Instructions

Copyright 2011, Chicago Pneumatic Tool Co. LLC

All  rights  reserved. Any  unauthorized  use  or  copying  of  the 

contents or part thereof is prohibited. This applies in particular to 

trademarks, model denominations, part numbers and drawings. 

Use only authorized parts. Any damage or malfunction caused 

by the use of unauthorized parts is not covered by Warranty or 

Product Liability.

Noise & Vibration Declaration*

Sound pressure level 83 dB(A), uncertainty 3 dB(A), 

in accordance with EN ISO 15744. For sound power, 

add 11 dB(A).

Vibration value CP9534:

a= 2,6 m/s², uncertainty k=1,1 m/s²

Vibration value CP9674 :

a= 2,5m/s², uncertainty k=1,2m/s²

re. ISO 28927-3

Declaration of noise and vibration emission

All values are current as of the date of this publication. For the 

latest information please visit cp.com.

These declared values were obtained by laboratory type 

testing in accordance with the stated standards and are 

suitable for comparison with the declared values of other 

tools tested in accordance with the same standards. These 

declared values are not adequate for use in risk assessments 

and values measured in individual work places may be higher. 

The actual exposure values and risk of harm experienced by 

an individual user are unique and depend upon the way the 

user works, the workpiece and the workstation design, as well 

upon the exposure time and the physical condition of the user.

We, Chicago Pneumatic, cannot be held liable for the 

consequences of using the declared values, instead of 

values reflecting the actual exposure, in an individual risk 

assessment in a work place situation over which we have no 

control. 

This tool may cause hand-arm vibration syndrome if its use is 

not adequately managed. An EU guide to managing hand-arm 

vibration can be found at http://www.humanvibration.com/EU/

VIBGUIDE.htm 

We recommend a programme of health surveillance to 

detect early symptoms which may relate to noise or vibration 

exposure, so that management procedures can be modified to 

help prevent future impairment. 

MANUFACTURER’S LIMITED WARRANTY

Limited  Warranty:    The  “Products”  of  the  Chicago  Pneumatic  Tool 

Co.  LLC  (“CP”)  are  warranted  to  be  free  from  defects  in  material  and 

workmanship  for  one  year  from  the  date  of  purchase.    This  Warranty 

applies only to Products purchased new from CP or its authorized dealers.  

Of  course,  this  Warranty  does  not  apply  to  products  which  have  been 

abused, misused, modified, or repaired by someone other than CP or its 

Authorized Service Representatives.  If a CP Product proves defective in 

material or workmanship within one year after purchase, return it to any 

CP  Factory  Service  Center  or Authorized  Service  Center  for  CP  tools, 

transportation  prepaid,  enclosing  your  name  and  address,  adequate 

proof of date of purchase, and a short description of the defect.  CP will, 

at its option, repair or replace defective Products free of charge.  Repairs 

or replacements are warranted as described above for the remainder of 

the original warranty period.  CP’s sole liability and your exclusive remedy 

under this Warranty is limited to repair or replacement of the defective 

Product. 

(There Are No Other Warranties Expressed Or Implied And 

CP  Shall  Not  Be  Liable  For  Incidental,  Consequential,  Or  Special 

Damages,  Or Any  Other  Damages,  Costs  Or  Expenses  Excepting 

Only The Cost Or Expense Of Repair Or Replacement As Described 

Above.)

INSTRUCTION MANUAL

Machine Type:

Pneumatic tool equipped with a flexible disc fitted 

with abrasive paper for sanding - No other use is 

permitted.

Air Supply Requirements

1. Supply tool with 90 psig (6.3 bar) of clean, dry air. 

Higher pressure drastically reduces tool life.

2. Connect tool to air line using pipe, hose and fitting 

sizes shown in the diagram below.

3. Do not install a quick coupler directly into the 

sander throttle handle.

Lubrication

  Use an air line lubricator with SAE #10 oil, adjusted 

to two drops per minute. If an air line lubricator 

cannot be used, add air motor oil to the inlet once a 

day.

Maintenance

1. Disassemble and inspect tool every three months 

if the tool is used every day. Replace damaged or 

worn parts.

Technical Data

                Free Speed          orbit diameter

CP9534:  9 600 RPM           3/16” - 5mm

CP9674:  12 000 RPM         3/8” - 10mm

Pad Size & type: 6” - 150mm Hook & Loop 

Air consumption: 19 cfm - 8,9 l/s

Air pressure 90 psi (6.3 bar)

Spindle size: 5/16”-24

English

EN