Chicago Pneumatic CP9104Q, Operator'S Manual

CP9104Q

Pencil Grinder

Original Instructions

Copyright 2010, Chicago Pneumatic Tool Co. LLC

All rights reserved. Any unauthorized use or copying of the contents 

or part thereof is prohibited. This applies in particular to trademarks, 

model  denominations,  part  numbers  and  drawings.  Use  only 

authorized parts. Any damage or malfunction caused by the use of 

unauthorized parts is not covered by Warranty or Product Liability.

Noise & Vibration Declaration

Sound pressure level 71 dB(A), uncertainty 3 dB(A), in 

accordance with EN ISO 15744. For sound power, add 11 

dB(A).

Vibration value;

<2.5 m/s

2

, re. ISO 20643.

Declaration of noise and vibration emission

All values are current as of the date of this publication. For the 

latest information please visit cp.com.

These declared values were obtained by laboratory type testing 

in accordance with the stated standards and are suitable for 

comparison with the declared values of other tools tested in 

accordance with the same standards. These declared values are 

not adequate for use in risk assessments and values measured in 

individual work places may be higher. The actual exposure values 

and risk of harm experienced by an individual user are unique 

and depend upon the way the user works, the workpiece and 

the workstation design, as well upon the exposure time and the 

physical condition of the user.

We, Chicago Pneumatic, cannot be held liable for the 

consequences of using the declared values, instead of values 

reflecting the actual exposure, in an individual risk assessment in a 

work place situation over which we have no control. 

This tool may cause hand-arm vibration syndrome if its use is 

not adequately managed. An EU guide to managing hand-arm 

vibration can be found at http://www.humanvibration.com/EU/

VIBGUIDE.htm 

We recommend a programme of health surveillance to detect early 

symptoms which may relate to noise or vibration exposure, so that 

management procedures can be modified to help prevent future 

impairment. 

MANUFACTURER’S LIMITED WARRANTY

Limited  Warranty:    The  “Products”  of  the  Chicago  Pneumatic  Tool 

Co.  LLC  (“CP”)  are  warranted  to  be  free  from  defects  in  material  and 

workmanship  for  one  year  from  the  date  of  purchase.    This  Warranty 

applies only to Products purchased new from CP or its authorized dealers.  

Of  course,  this  Warranty  does  not  apply  to  products  which  have  been 

abused, misused, modified, or repaired by someone other than CP or its 

Authorized Service Representatives.  If a CP Product proves defective in 

material or workmanship within one year after purchase, return it to any 

CP  Factory  Service  Center  or Authorized  Service  Center  for  CP  tools, 

transportation  prepaid,  enclosing  your  name  and  address,  adequate 

proof of date of purchase, and a short description of the defect.  CP will, 

at its option, repair or replace defective Products free of charge.  Repairs 

or replacements are warranted as described above for the remainder of 

the original warranty period.  CP’s sole liability and your exclusive remedy 

under this Warranty is limited to repair or replacement of the defective 

Product. 

(There Are No Other Warranties Expressed Or Implied And 

CP  Shall  Not  Be  Liable  For  Incidental,  Consequential,  Or  Special 

Damages,  Or Any  Other  Damages,  Costs  Or  Expenses  Excepting 

Only The Cost Or Expense Of Repair Or Replacement As Described 

Above.)

INSTRUCTION MANUAL

Machine Type:

Power tool equipped with 1/8in. or 3mm collet chuck for use 

with various burrs for polishing and grinding - No other use is 
permitted.

Air Supply Requirements

1.  Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher 

pressure drastically reduces tool life.

2.  Connect tool to air line using pipe, hose and fitting sizes 

shown in the diagram below.

3.  Do not install a quick coupler directly into the sander 

throttle handle.

Lubrication

  Use an air line lubricator with SAE #10 oil, adjusted to two 

drops per minute. If an air line lubricator cannot be used, 
add air motor oil to the inlet once a day.

Maintenance

1.  After first year disassemble and inspect tool every three 

months if the tool is used every day. Replace damaged or 

worn parts.

2.  High wear parts are underlined in the parts list

Technical Data

1/8in. or 3mm Collets

Free speed; 60,000 RPM

Air pressure 90 psi (6.3 bar)

Air comsumption; 7 cfm (3.3 l/s)

English

EN

1/2" (12mm)

1/2" (12mm)

CA048361 (1/2") NPT

CA048362 (1/2") NPT

CA048360 (1/2") NPT

3/8" (10mm)

1/4 NPT

130

90

0