background image

The Company warrants that the Equipment manufactured by it   and delivered hereunder shall be free from  defects  in  material  and  
workmanship  for  a  period  of twelve  (12)  months  from  the date of initial  start-up, or  eighteen   (18)  months  from  the  date  of  
shipment from the manufacturer,  whichever  occurs  first.  The  foregoing warranty period shall apply to all Equipment, except for the 
following:  (A)  all two stage reciprocating stationary   models  are warranted  for  the earlier of twenty-four (24) months from the date of 
initial operation or thirty  (30)  months  from  date  of  shipment  from  the  manufacturer.  (B)  Replacement parts  will be warranted for 
three (3) months from  the  date of shipment from  the  manufacturer.  Should  the  failure  to  conform  to  this  warranty   be   reported   in   
writing  to  the  Company  within  said  period,   the  Company  shall,  at  its  option,  correct  such  non - conformity   by  suitable  repair  to  
such  Equipment,  or  furnish  a  replacement  part  F.O.B  point  of  shipment,  provided that the Purchaser has  installed,  maintained,  
and  operated  such  Equipment in accordance  with  good   industry practices, and has complied with specific  recommendations  of   the  
Company.       Accessories     and     equipment     furnished     by     the   Company,     but   manufactured   by   others,   shall carry whatever 
warranty the manufacturer conveyed to the Company and   which can   be passed on   to   the Purchaser.   The Company shall   not   be   
liable for  any  repairs,  replacements,  or  adjustments  to  the  Equipment,  or  any  costs of labor performed by the Purchaser without the 
Company’s prior written approval.

The Company makes no performance warranty unless specifically stated within its proposal, and the effects of corrosion, erosion, 
and normal wear and tear are specifically excluded from the  Company’s  warranty.  In  the  event  performance  warranties  are  
expressly included, the Company’s obligation shall be to correct in the manner and for the period of time provided above.

THE    COMPANY    MAKES    NO    OTHER     WARRANTY    OR    REPRESENTATION    OF   ANY   KIND 

WHATSOEVER,    EXPRESSED    OR    IMPLIED,   EXCEPT   THAT    OF   TITLE,    AND    ALL    IMPLIED   

WARRANTIES   OF    MERCHANTABILITY    AND   FITNESS    FOR    A   PARTICULAR   PURPOSE,   ARE 

HEREBY   DISCLAIMED.  THIS WARRANTY SUPERSEDES ALL PREVIOUS WARRANTY STATEMENTS.

Correction by the Company of non-conformities, whether patent or latent, in the manner and for the  period  of  time  provided  
above, shall constitute fulfillment of all liabilities of the Company and its distributors for such non-conformities with respect to, or 
arising out of such Equipment.

LIMITATION OF LIABILITY

THE REMEDIES OF THE  PURCHASER  SET  FORTH   HEREIN  ARE  EXCLUSIVE,  AND THE TOTAL 
LIABILITY OF THE COMPANY, ITS DISTRIBUTORS AND SUPPLIERS WITH RESPECT TO CONTRACT OR 
THE EQUIPMENT AND SERVICES FURNISHED IN CONNECTION WITH THE  PERFORMANCE  OR  
BREACH  THEREOF,  OR  FROM THE  MANUFACTURE, SALE,   DELIVERY,   INSTALLATION,    REPAIR  OR   
TECHNICAL   DIRECTION   COVERED   OR   FURNISHED  UNDER CONTRACT,  WHETHER  BASED  ON  
CONTRACT,  WARRANTY,  NEGLIGENCE,  INDEMNITY,  STRICT  LIABILITY OR OTHERWISE,  SHALL  NOT  
EXCEED  THE  PURCHASE  PRICE OF THE EQUIPMENT UPON WHICH SUCH LIABILITY IS BASED.

THE  COMPANY,  ITS  DISTRIBUTORS AND  ITS  SUPPLIERS  SHALL  IN  NO  EVENT BE LIABLE TO THE 
PURCHASER, ANY   SUCCESSORS   IN   INTEREST,    OR   ANY   BENEFICIARY   OR   ASSIGNEE   OF    THE   
CONTRACT   FOR   ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT,  SPECIAL OR PUNITIVE DAMAGES  
ARISING  OUT  OF  THIS  CONTRACT OR ANY  BREACH  THEREOF,   OR  ANY  DEFECT  IN,   OR  FAILURE  OF,   
OR  MALFUNCTION  OF  THE  EQUIPMENT, WHETHER OR NOT BASED ON LOSS  OF  USE,  LOST  PROFITS  
OR  REVENUE,  INTEREST,  LOST GOODWILL,  WORK STOPPAGE,  IMPAIRMENT  OF  OTHER  GOODS,  LOSS  
BY  REASON  OF  SHUTDOWN OR NON-OPERATION, COST OF PURCHASE OF REPLACEMENT POWER,  OR 
CLAIMS OF PURCHASER OR CUSTOMERS OF PURCHASER FOR SERVICE INTERRUPTION, WHETHER OR 
NOT SUCH LOSS OR DAMAGE IS BASED ON CONTRACT,  WARRANTY, NEGLIGENCE, INDEMNITY, STRICT 
LIABILITY OR OTHERWISE.

Warranty Statement

Chicago Pneumatic Compressors

1800 Overview Drive

Rock Hill, SC 29730

866-869-3114 (Parts and Technical)

Summary of Contents for RCP Series


























Reviews: