background image

MFAUBSP

Installation Instructions

10

Pitch Adjustment

5.

Turn pitch adjustment knob clockwise to tilt display forward.
(See Figure 13)

6.

Turn pitch adjustment knob counterclockwise to tilt display
back. (See Figure 13)

Roll Adjustment

7.

Turn roll adjustment knob clockwise to adjust roll to the left.
(See Figure 13)

8.

Turn roll adjustment knob counterclockwise to adjust roll to
the right. (See Figure 13)

Figure 13

Stand Use and Maintenance

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components located between the MFAUBSP up to (and
including) the display does not exceed 125 lbs (56.7 kg).

WARNING:

RISK OF SERIOUS INJURY OR DEATH!

Placing a remote control or toy on the stand may encourage
a child to climb onto the stand causing the stand to tip over
onto the child. DO NOT place remote controls or toys on the
stand!

WARNING:

 RISK OF SERIOUS INJURY OR DEATH!

Relocating audio and/or video equipment to the stand may
result in the stand collapsing or overturning onto a child. DO
NOT relocate audio and/or video equipment to the stand!

WARNING:

STAND CAN TIP OVER RESULTING IN RISK

OF INJURY. Never move the stand when displays are
attached. Never push against the stand.

NOTE:

The MFAUBSP stand has no user serviceable parts.

1.

Always place stand on a level surface.

pitch adjustment

knob

roll adjustment

knob

5

6

7

8

7

8

6

5

Summary of Contents for MFAUBSP













Reviews: