CHIEF MSP-DCCPPNR Installation Instructions Manual Download

Page: 2 / 14

Installation Instructions

MSP-DCCPPNR

IMPORTANT WARNINGS AND CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions.

CAUTION:

CAUTION

alerts you to the possibility of damage or destruction of equipment if you do not follow the cor-

responding instructions.

•

WARNING:

Improper installation can result in serious personal injury! Make sure that the structural members can
support a redundant weight factor five times the total weight of the equipment: if not, reinforce the
structure before installing the mount.

•

WARNING:

Be aware also of the potential for personal injury or damage to the unit if it is not adequately mounted.

•

WARNING:

The installer is responsible for verifying that the wall to which the mount is anchored will safely support
the combined load of all attached components or other equipment

•

WARNING:

The weight of the display placed on the mount must not exceed 200 lbs. (90.72kg), the maximum load
capacity of the mount

•

WARNING:

Watch for pinch points. Do not put your fingers between movable parts.

•

WARNING:

Make sure the mount and brackets are correctly oriented.

•

WARNING:

Make sure the flag securing the display is completely lowered at all times except when removing or
installing the display.

•

CAUTION:

Check the unit for shipping damage before you begin the installation.

NOTE: Hardware for attaching this unit to the wall is not supplied.

CONTENTS

IMPORTANT WARNINGS AND CAUTIONS! .....................................

DIMENSIONAL DRAWING .................................................................

INSPECT THE UNIT BEFORE INSTALLING .....................................

MOUNT SPECIFICATIONS ................................................................

INTERFACES .....................................................................................

TOOLS REQUIRED FOR INSTALLATION .........................................

PARTS LIST .......................................................................................

MOUNT INSTALLATION ....................................................................

Mount the mount ...........................................................................

Adjust Height on the mount ..........................................................

MOUNT THE DISPLAY ......................................................................

CABLE MANAGEMENT .....................................................................

TENSION ADJUSTMENTS ................................................................ 10

Vertical Tilt Tension Adjustment ................................................... 10

Lateral Tilt Tension Adjustment .................................................... 10

Rotational Tilt Tension Adjustment ............................................... 10

SWING ARM ADJUSTMENTS ........................................................... 11

Adjusting the Swing Arms Slightly Off Center Adjustment ........... 11

Reconfiguring the Swing Arms to the Left or Right of Center ....... 12

REMOVE THE DISPLAY .................................................................... 12

Swing Arm Tension Adjustment ........................................................... 13

Summary of Contents for MSP-DCCPPNR















Search results

Summary of Contents for MSP-DCCPPNR

Reviews:

Related manuals for MSP-DCCPPNR

Brands by name

Popular brands

CHIEF MSP-DCCPPNR, Installation Instructions Manual

Search results

Summary of Contents for MSP-DCCPPNR

Reviews:

Related manuals for MSP-DCCPPNR

Brands by name

Popular brands