background image

5

Installation Instructions

MSP-DCCPPNR

MOUNT INSTALLATION

WARNING: Improper installation can result in serious 

personal injury!

WARNING: It is the responsibility of the installer to verify 

that the wall to which the mount is anchored 
will safely support five times 
the combined 
load of all attached components and equip-
ment. If not, reinforce the structure before 
installing the mount.

Locate two wood studs 16” apart on center

1.

Determine the exact mounting location prior to installa-
tion, considering screen size and the unit’s total swing 
arm radius. Keep in mind that the mount must be 
mounted to wood studs that are 16” apart on center.

NOTE: Mount the mount between parallel wall studs 

or other supporting framework that is vertical 
or horizontal.

2.

Using a stud sensor, locate the two wood studs where 
you will install the mount.

3.

Draw a level plumb line to indicate the desired height of 
the top mounting bracket.

4.

With an assistant, lift and hold the mount against wall. 
Use a pencil, awl, or small nail to mark the mounting 
holes where two pilot holes will be drilled into the cen-
ter of the wood studs. Make sure the mounting holes are 
level.

5.

With an assistant, lay the mount down on the floor.

6.

Drill two pilot holes where the mounting holes were 
marked for anchoring the top bracket on the mount. See 
Figure 1.

NOTE: Do not tighten the lag bolts down at this time. 

Leave enough space between the wall and lag 
bolts to hang the mount.

7.

Install two lag bolts and two flat washers, in the pilot 
holes drilled in step 6.

Figure 1. Two Wood Studs 16” Apart On Center

16”

Wood Studs 

Pilot Holes 

Wall 

Summary of Contents for MSP-DCCPPNR















Reviews: