CHIEF PNR Installation Instructions Manual Download

Page: 10 / 14

Model PNR™

Installation Instructions

ADJUSTMENTS

TENSION ADJUSTMENTS

Vertical Tilt Tension Adjustment

1. Using 5/32” Allen wrench, slightly tighten or loosen

two screws, one on each side, equally (See figure 9).

2. With display mounted, check for desired vertical tilt

tension.

3. Repeat Step 1 and Step 2 until desired vertical tilt

tension is obtained.

Lateral Tilt Tension Adjustment

CAUTION:

Overtightening lateral adjustment will

cause excessive wear and may distort adjustment
components.

1. Using a 9/16” wrench (not provided), slightly tighten or

loosen lateral tilt tension adjustment nut

(See figure 10).

2. Mount the display and check for desired tilt tension.

3. Repeat Steps 1 and 2 until desired tilt tension is

obtained.

Rotational Tilt Tension Adjustment

1. If necessary, loosen or tighten bottom rotational tilt

tension adjustment nut (See figure 10).

2. Mount the display and check for desired rotational tilt

tension.

3. Repeat Steps 1 and 2 until desired rotational tilt

tension is obtained.

Figure 9: Vertical Tilt

Figure 10: Lateral and Rotational Adjustment

Vertical Tilt

Adj. Screw

Rotational Tilt
Adjustment Nut

Lateral Tilt
Adjustment Nut

Summary of Contents for PNR















Search results

Summary of Contents for PNR

Reviews:

Related manuals for PNR

Brands by name

Popular brands

CHIEF PNR, Installation Instructions Manual

Search results

Summary of Contents for PNR

Reviews:

Related manuals for PNR

Brands by name

Popular brands