background image

PTS SERIES

Installation Instructions

2

DISCLAIMER

CSAV, Inc., and its affiliated corporations and subsidiaries
(collectively, "CSAV"), intend to make this manual accurate and
complete. However, CSAV makes no claim that the information
contained herein covers all details, conditions or variations, nor
does it provide for every possible contingency in connection
with the installation or use of this product. The information
contained in this document is subject to change without notice
or obligation of any kind. CSAV makes no representation of
warranty, expressed or implied, regarding the information
contained herein. CSAV assumes no responsibility for
accuracy, completeness or sufficiency of the information
contained in this document.

 IMPORTANT WARNINGS AND

CAUTIONS!

WARNING:

A WARNING alerts you to the possibility of

serious injury or death if you do not follow the instructions.

CAUTION:

A CAUTION alerts you to the possibility of

damage or destruction of equipment if you do not follow the
corresponding instructions.

WARNING:

Failure to read, thoroughly understand, and

follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty!  It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.

WARNING:

Failure to provide adequate structural strength

for this component can result in serious personal injury or
damage to equipment!  It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components located between the supporting structure and
mount up to (and including) the display does not exceed

100 lbs (45.36 kg)

.

DIMENSIONS

[102]
4.00

[18]
 .70

[581]
22.88

       

[360  50.80]

        

14.17  2.0

       TO APPROX.
CENTER OF SCREEN

+

+

[606]
23.88

 [276]
10.86

[176]
 6.92

[114]
4.50

NOTE:  CUSTOM INTERFACE BRACKET
NOT SHOWN. THE CUSTOM INTERFACE
BRACKET NEEDED FOR YOUR DISPLAY
WILL ADD BETWEEN ½”AND 2” IN DEPTH
AND MAY AFFECT LOCATION OF DISPLAY
ON THE MOUNT.

MEASUREMENTS IN:    [MILLIMETERS]
                                              INCHES

WEIGHT CAPACITY:       100 LBS
HEIGHT ADJUSTMENT:  4” IN 1” INCREMENTS
TILT/ROLL:                      

0°/  2.5°

+

+

Summary of Contents for PTS Series









Reviews: