background image

 PWRSKU

Installation Instructions

2

DISCLAIMER

Milestone AV Technologies, and its affiliated corporations and 
subsidiaries (collectively, "Milestone"), intend to make this 
manual accurate and complete. However, Milestone makes no 
claim that the information contained herein covers all details, 
conditions or variations, nor does it provide for every possible 
contingency in connection with the installation or use of this 
product. The information contained in this document is subject 
to change without notice or obligation of any kind. Milestone 
makes no representation of warranty, expressed or implied, 
regarding the information contained herein. Milestone assumes 
no responsibility for accuracy, completeness or sufficiency of 
the information contained in this document.
Chief® and ClickConnect™ are registered trademarks of 
Milestone AV Technologies. All rights reserved.

 IMPORTANT WARNINGS AND 

CAUTIONS!

WARNING:  

A WARNING alerts you to the possibility of 

serious injury or death if you do not follow the instructions.

CAUTION:  

A CAUTION alerts you to the possibility of 

damage or destruction of equipment if you do not follow the 

corresponding instructions.

WARNING:  

Failure to read, thoroughly understand, and 

follow all instructions can result in serious personal injury, 
damage to equipment, or voiding of factory warranty!  It is the 
installer’s responsibility to make sure all components are 
properly assembled and installed using the instructions 
provided.

WARNING:  

Failure to provide adequate structural strength 

for the installation of this kit can result in serious personal 
injury or damage to equipment!  It is the installer’s 
responsibility to make sure the structure to which this mount 
is attached can support five times the combined weight of all 
equipment.

WARNING:  

Exceeding the weight capacity can result in 

serious personal injury or damage to equipment!  It is the 
installer’s responsibility to make sure the combined weight of 
all components attached to this accessory does not exceed 
100lbs  (45.3 kg) if  being installed on a wall with a minimum 
1/2" thick drywall, or 125 lbs (56.7 kg) if  being installed on a 
wall with a minimum 5/8" thick drywall.

LEGEND

Tighten Fastener

Apretar elemento de fijación

Befestigungsteil festziehen

Apertar fixador

Serrare il fissaggio

Bevestiging vastdraaien

Serrez les fixations

Сожмите

 

Застежку

Loosen Fastener

Aflojar elemento de fijación

Befestigungsteil lösen

Desapertar fixador

Allentare il fissaggio

Bevestiging losdraaien

Desserrez les fixations

Ослабьте

 

Застежку

Open-Ended Wrench

Llave de boca

Gabelschlüssel

Chave de bocas

Chiave a punte aperte

Steeksleutel

Clé à fourche

Открытый

 

Рывок

Adjust

Ajustar

Einstellen

Ajustar

Regolare

Afstellen

Ajuster

Приспособьтесь

Phillips Screwdriver

Destornillador Phillips

Kreuzschlitzschraubendreher

Chave de fendas Phillips

Cacciavite a stella

Kruiskopschroevendraaier

Tournevis à pointe cruciforme

Отвертка

Hex-Head Wrench

Llave de cabeza hexagonal

Sechskantschlüssel

Chave de cabeça sextavada

Chiave esagonale

Zeskantsleutel

Clé à tête hexagonale

Главный

 

ведьмой

 

Рывок

Summary of Contents for PWRSKU













Reviews: