background image

I N S T A L L A T I O N       I N S T R U C T I O N S  

 

CHIEF MANUFACTURING INC. 

8809-000027 (Rev. A) 

1-800-582-6480

  952-894-6280 FAX 952-894-6918 

2004 Chief Manufacturing 

8401 EAGLE CREEK PARKWAY, STE. 700 

www.chiefmfg.com

 

SAVAGE, MINNESOTA 55378  USA 

11/04 

 

CTA-025 

Single Stud Wall Arm 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

BEFORE YOU BEGIN  

 

• 

CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty, 
thoroughly study all instructions and illustrations before you begin to install the CTA-025. Pay particular 
attention to the Warnings and Cautions in this document. 

 

• 

If you have any questions about this installation, contact Chief Manufacturing at 1-800-582-6480 or 952-582-6480.

The CTA-025 Single Stud Wall Arm can be used to 
wall mount RPA, UPC or LCDA series ceiling 
mounts.  

The CTA-025 also provides a mounting solution for 
TV/Monitor mounts. The CTA-025 has a maximum 
weight capacity of 150 lbs (68.0 kg). 

The wall arm on the CTA-025 is 25.0” in length from 
the wall mount.

 

 

CTA-025 Single Stud Wall Arm 

Summary of Contents for Single Stud Wall Arm CTA-025







Reviews: