background image

チコーエアーテック株式会社 

Copyright CHIKO AIRTEC CO., LTD. 2009 

 

 

 

  14

 

 

 

 

 

6

 

保守・点検 

Maintenance and Inspection

 

6.1 

保守点検時の注意事項

Cautions on maintenance and inspection

 

 

 

6.2 

フィルタの交換時期について 

Filter replacement timing

 

フィルタ目詰の

C.F

表示が点灯しましたら、1次フィルタを交換してください。

 

また、1次フィルタを交換しても、目詰まり表示が消えないときには、2次フィルタを交換してください。

 

If the filter replacement indicator lamp does not turn OFF even after replacement of the primary filter 
(filter bag), replace the secondary (main) filter. 

 

 

フィルタ取付の際には、裏・表を間違えないようご注意ください

 

(フィルタ格子の枠が排気面側です)

 

Do not confuse the back and front of the filter. 
(The filter grid frame should be located on the exhaust side.) 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

点検時は必ず電源を切り、コンセントからプラグを抜いて、電路遮断を

 

行ってください。

 

Make sure to turn OFF the main power, and disconnect the power plug 
from the electrical outlet to cut off the electricity before starting 
inspection.

 

 

摩耗や破損したフィルタをそのまま使用すると、吸込んだ粉塵を大気に再飛散
させ、電気部品の損傷となります。

 

機械の故障、事故を未然に防ぎ、

 

末永くご使用頂けますよう、点検、手入れは必ず行ってください。

 

Using a worn or damaged filter will release sucked dust to the 
atmosphere, and damage electrical parts. 
Make sure to inspect and maintain, to prevent failures and accidents in 
the product and use the product for a long time.

 

 

フィルタの交換時は、電源を切り、

 

コンセントからプラグを抜いて、電路遮断を行ってください。

 

Make sure to turn OFF the power, and disconnect the power plug from 
the electrical outlet before starting inspection.

 

Summary of Contents for CHV-030AD-HC-V1




















Reviews: