Chapter 4
Various settings (mode select mode)
48
1.
Move to the MODE SELECT mode.
2.
Press the Up/Down arrow buttons to move to the communication format setting mode
(“Com Setting”).
3.
Press the ENTER button.
The communication station number check screen appears, showing the current settings.
4.
Press the Up/ Down arrow buttons to move to the item you want to set.
5.
Press the ENTER button.
The setting screen appears.
6.
Press the Up/Down arrow buttons to select the desired setting.
7.
Press the ENTER button to determine the setting.
8.
To exit this mode, press the MODE SELECT button to return to normal mode.
4.3
Air Volume-Down Alert Timing Setting Mode
This mode allows for changing the timing for displaying an air volume-down warning (WARN4) as desired.
1.
Move to the MODE SELECT mode.
2.
Press the Up/Down arrow buttons to move to the air volume-down alert timing setting mode
(“Volume Down ST”).
3.
Press the ENTER button.
The current setting appears.
The default is 50%, displayed as “3: Down to 50%”.
4.
Press the Up/Down arrow buttons to select a timing between 30 to 70%.
A lower setting causes the air volume-down alert to occur later, and vice versa.
5.
Press the ENTER button to determine the setting.
6.
To exit this mode, press the MODE SELECT button to return to normal mode.
4.4
Pulse control setting mode
Sets Pulse control interval time and AUTO enable/disable.
■
Interval time
1.
Press the MODE SELECT button.
2.
Press
↑
or
↓
to switch to Pulse control setting mode [Pulse Setting].
(
This step is omitted if the unit is in operation. Go to Step 3.
)
3.
Press the Enter button. The confirmation screen for interval time is shown and current settings are
displayed.
The standard factory setting is 15 minutes.
4.
Press the Enter button. Switches to the settings screen.
5.
Press
←
or
→
to move the 3-digit cursor. Press
↑
or
↓
to change value.
6.
Press the Enter button to set value.
7.
To exit this mode, press the MODE SELECT button to return to normal mode.
Summary of Contents for CMP-2500AT3-A
