background image

 
 
 

6.3 

1次フィルタの交換 

Replacement of primary

 

 
 
 
 
 
 
 
 
 
 
 

6.4 

2次フィルタの交換 

Replacement of 

 
 
 
 
 
 
 
 
 
 
 

6.5 

排気フィルタの交換

 

Replacement of 

 
 
 
 
 
 
 
 
 
 
 
 

 

 

フィルタ取り付

Do not confuse the back and front of the filter.

①パッチン錠左右の2ヶ所を外します

Release two snap locks on the left and 
right sides.

 

Copyright  CHIKO  AIRTEC  CO.,

 

  14

 

 

Replacement of primary filter

 

 
 
 
 
 
 
 
 

Replacement of secondary filter

 

Replacement of exhaust filter

 

付けは、裏・表を間違えないで下さい。

 

Do not confuse the back and front of the filter. 

①フィルタケースのパッチン

Release the snap locks of the filter case.

②フィルタケースの円筒パイプにフィルタ
込んでいますので、下に向かって軽く

The filter paper packing of the primary filter is inserted 
into the cylindrical pipe of the filter case.   
Lightly push down the filter paper packing to remove it.

します 

snap locks on the left and 

②排気口扉を外し、排気フィルタを取

Remove the exhaust port door, and take out the exhaust filter.

①フィルタ室内  2か所  蝶ナットを外
持ち上げて下さい。 
②フィルタ枠から2次フィルタを下部方向
い。

 

チコーエアーテック株式会社 

Copyright  CHIKO  AIRTEC  CO.,  LTD.  2009

 

 

 
 

フィルタケースのパッチン錠を外します 

Release the snap locks of the filter case.

 

パイプにフィルタ紙パッキン部を差し

く押さえて、取り外します。

 

The filter paper packing of the primary filter is inserted 
into the cylindrical pipe of the filter case.     
Lightly push down the filter paper packing to remove it. 

取り出します 

Remove the exhaust port door, and take out the exhaust filter.

 

外し、フィルタ枠を上側に

下部方向に抜き取って下さ

Summary of Contents for CKU-400AT-HC-V1




















Reviews: