background image

Chiltern Invadex Side Entry MK2

6

Installation details 

(use fig 3 with instructions)

Fig 3

10

2

8

3

9

1

7

6

4

5

User Guide

15

Rub clean head of

handset to clear any

scale build up.

See note 1 below.

Check unit is on

maximum heat setting/

reduce flow.

Turn down the tempera-

ture and try again, Pump

needs cleaning.

Unblock waste hose.

This is normal. The water

left in the waste hose

when the pump stops will

run back when the pump

stops.

The shower should be run

for a couple of minutes

after use to ensure that

clean.

Mixer Showers

Reduced flow of water

from the shower head.

Electric Showers

Reduced flow of water

from the shower head.

Temperature of showering

water is too cool.

Shower cuts out.

Pumped shower  waste

Water level higher than

normal.

Unpleasant odour
from cubicle

Troubleshooting

symptom

suggested cause

solution

Note 1:

 *Water supply presssures may be affected by simultaneous use of

water at another point in the house, a fault in the house plumbing or a
problem with the water supply to the house.

For further assistance please telephone your nearest Chiltern Invadex
Regional Office.  Remember that the service calls made after the expiry of
the guarantee will be chargeable.  If maintenance of the equipment is the
responsibility of a third party, for example the Social Services, please
contact them in the first instance.

Spray rings in the shower

head have a build up of

limescale and need

cleaning.

Water supply* pressure

is lower than normal.

Water supply is colder

than normal, possibly due

to weather conditons.

Water supply* pressure is

lower than normal.

Temperature is set higher

than safety cut-out.

Spray rings in the shower

head have a buid up of

lime-scale and need

cleaning.

Water supply* pressure is

lower than normal.

Waste hose is blocked.

Water left in gully at back

of  shower after use.

Stagnant soapy water in

the back gully.

the residual water is

Summary of Contents for Side Entry Mk2
























Reviews: