Chima STCS4012 Series Installation Manual Download

Page: 20 / 21

STCS4012 Series Layer 3 Switch Installation Guide

- - 15 - -

www.stephen-tele.com

Booting ......................................

Aux Port Init 100 half down ................... OK

No inet address specified for interface dc.

Switch Firmware Init ........................... OK

Check Timebase: 16.500126 MHz ................... OK

Check PCI: 33.000252 MHz ........................ OK

Check CPU: 198.001512 MHz ....................... OK

Switch Firmware Init ........................... OK

Layer 2 Application ............................. OK

Layer 3 Application ............................. OK

Entering SPROS ......

Initializing environment ...... Done.

Loading startup config ...... Done.

============================================================

|| ||

|| Welcome to SPROS. ||

|| ||

|| Press Return to connect and config this system. ||

|| ||

============================================================

The information above indicates the completion of switch auto-booting.

Press <Enter> and the following information will be displayed.

Welcome to Routing system

：

Now you can begin configuring the switch.

Summary of Contents for STCS4012 Series






















Search results

Summary of Contents for STCS4012 Series

Reviews:

Related manuals for STCS4012 Series

Brands by name

Popular brands

Chima STCS4012 Series, Installation Manual

Search results

Summary of Contents for STCS4012 Series

Reviews:

Related manuals for STCS4012 Series

Brands by name

Popular brands