background image

 

CS-8 ol HDH6/VDL6 Rev1.04, Feb. 2015 

 

-6-

 

PLEASE AVOID SHARP BENDING OF ANY CORDS AND CABLES. 

 

CORDS SHOULD NOT BE INSTALLED WITHIN THE REACH OF CHILDREN 
OR PETS. 

 

DO NOT TREAD THE ENCLOSURE OF THE PRODUCT, DO NOT PLACE 
HEAVY OBJECTS ON IT. 

 

BEFORE REMOVING THE PRODUCT FROM THE RACK, PLEASE 
DISCONNECT THE POWER PLUG AND ALL OTHER CABLE 
CONNECTIONS.  

 

PLEASE DISCONNECT THE POWER PLUG FROM THE OUTLET IN CASE OF 
A THUNDERSTORM. 

 

NEVER OPEN THE ENCLOSURE OF THE PRODUCT! NEVER TRY TO 
MODIFY  THE INTERNAL CIRCUITRY! ONLY QUALIFIED SERVICE 
PERSONNEL IS ALLOWED TO OPEN THE ENCLOSURE.  

 

DO NOT PLACE OPEN FIRE ON TOP OF THE PRODUCT (CANDLES, ASH 
TRAYS, HOT THAI CURRIES ETC). 

 

NEVER EXPOSE THE PRODUCT TO WATER, BEER, OR MOISTURE. 

 

ADULTS ARE TO MAKE SURE THAT CHILDREN FOLLOW ALL SAFETY 
INSTRUCTIONS. SAME THING GOES FOR PETS. 

 

AVOID MECHANICAL STRESS OR IMPACT. DO NOT DROP THE PRODUCT; 
EVEN IF THERE IS A CONTROL LABELLED "DROP"!. 

 

DO NOT USE THE PRODUCT WITH TOO MANY OTHER ELECTRONIC 
DEVICES RUNNING FROM ONE SINGLE OUTLET, ESPECIALLY IN 
CONNECTION WITH EXTENSION CORDS. DO NOT ATTEMPT TO SAVE 
MONEY ON CHEAP SOLUTIONS. BUY PROPER HIGH-DUTY POWER 
DISTRIBUTORS AND CORDS! 

 

NEVER USE EXTENSION CORDS WITH LESS MAXIMUM LOAD THAN THE 
TOTAL POWER CONSUMPTION OF ALL DEVICES CONNECTED TO A 
SINGLE POWER OUTLET COMBINED. OVERLOADING EXTENSION CORDS 
CAN CAUSE FIRE. 

 

AVOID MECHANICAL STRESS ON SOCKETS AND KNOBS / SWITCHES. 

 

PROTECT YOUR SPEAKERS AND EARS (!) AGAINST EXCESSIVE AUDIO 

LEVELS. THE CS-8 PHS-28 UNIT IS CAPABLE OF GENERATING 

EXTREMELY LOW AS WELL AS EXTREMELY HIGH FREQUENCIES. BOTH 

MIGHT CAUSE SERIOUS DAMAGE TO AUDIO EQUIPMENT AND EAR-

DRUMS! 

 
 
5. MAINTAINANCE/ CLEANING 

Summary of Contents for CS-8 ol HDH6





















Reviews: