Chloride 2000 Operating Instructions Manual Download

Page: 31 / 234

Chloride Active

4.4.3.2 Normal Start-up Procedure

Units with LED indicators

Units with LCD display

Following 4.4.2.2, power should be available to the

connected equipment via internal bypass once the

input has been connected to the AC mains (if AC mains

power is available).

Press the inverter ON/OFF button to switch on the

inverter; or press twice if AC power is not present and

cold start is enabled to start up in battery mode.

The UPS will respond with some beeps and illuminations

of LED indicators.

If AC power is present, the UPS will turn on the Line

Mode LED and inverter ON LED indicating that the unit

is now in line mode.

If AC power is not present and cold start function is

enabled, the UPS will turn on the Battery Mode LED

and inverter ON LED indicating that the unit is now

providing output power from the battery.

ATTENTION:

If the overload indicator is on, or the

“LOAD” indicator is beyond 100%, there are too many

devices connected to the UPS. If only one device is

connected to the UPS and the overload indicator is

on, then the load’s power demand exceeds the rating

of the UPS, and a UPS with a higher power rating

must be used.

NOTE:

If the UPS does not respond as above, please

see section 7 (“Troubleshooting”).

Following 4.4.2.2, power should be available to the

connected equipment via internal bypass once the

input has been connected to the AC mains (if AC mains

power is available).

Press the inverter ON/OFF button to switch on the

inverter; or press twice if AC power is not present and

cold start is enabled to start up in battery mode.

The UPS will respond with some beeps and illuminations

of LED indicators.

If AC power is present, the UPS will turn on the Mains

LED and inverter ON LED indicating that the unit is

now in line mode. The LCD Display will show the

message LOAD PROTECTED and will indicate the

output power.

If AC power is not present and cold start function is

enabled, the UPS will turn on the Inverter ON LED

(but not the Mains LED) indicating that the unit is now

providing output power from the battery. The LCD Display

will show the message MAINS FAILURE and will indicate

the estimated remaining back-up time.

ATTENTION:

If the display shows a message indicating

OVERLOAD, there are too many devices connected to

the UPS. If only one device is connected to the UPS and

the display shows a message indicating OVERLOAD,

then the load’s power demand exceeds the rating of

the UPS, and a UPS with a higher power rating must

be used

NOTE:

If the UPS does not respond as above, please

see section 7 (“Troubleshooting”).

4.4.4 Forced Bypass Procedure

Units with LED indicators

Units with LCD display

To place the UPS into bypass mode, press and hold

buttons 5 and 6 for four seconds (see

gures on section

4.2.1). The UPS will switch to bypass mode and the

Bypass Mode LED will illuminate. Follow the same

procedure to make the UPS return to line mode.

For other details regarding bypass mode operation,

please see section 4.1.3.

To place the UPS into bypass mode, go to Menu 6

(Advanced Options) and then to submenu “Manual

Bypass” and select TURN UPS TO BYPASS. Follow the

same procedure to make the UPS return to line mode,

selecting TURN UPS TO ONLINE in the same menu.

For other details regarding bypass mode operation,

please see section 4.1.3.

4.4.5 ECO Mode Activation/Deactivation Procedure

NOTE:

this functionality cannot be enabled / disabled using front panel buttons in units with front panel

based on LED indicators

In order to enable ECO mode, follow this procedure: with the unit operating in line mode, go to Menu 6
(Advanced options) and then to submenu “ECO Mode” and select ECO MODE ENABLE. The unit will start
to operate in this mode immediately.

To return the unit to line mode, follow the same procedure, now selecting ECO MODE DISABLE.

For other details regarding ECO mode operation, please see section 4.1.4