background image

NEXGEN50R InstallationRev2 

Page 

26

 of 

38

 04/11/2022

 

 

Note:  

Sulfuric acid and dry acid (sodium bisulfate) are not recommended for pH 

adjustment.  Under some conditions the electrolytic cell can be damaged. 

 

WARNING 

Read all cautions and directions provided with the muriatic acid used.  Always add acid 
to water.  Use only with adequate ventilation.  If strong odor is noticed, STOP, ventilation 
is inadequate.  Leave area immediately.  If the work area is not well ventilated you MUST 
use a properly fitted and maintained NIOSH approved respirator for acid fumes. 

 
 

Fill the acid wash tank with a 5 to 1 water / muriatic acid solution.   

 
 

Press NEXT to continue. 
 

 

All valves on the NEXGEN are clearly marked with valve tags.  The valves to be adjusted 
in each step will be flashing on the screen. 

 

STEP 1 

– Close the Tank Fill Valve marked 3.  Close the Product Flow Adjustment Valve 

marked 4.  This will allow the tank to drain for cleaning. 
 
Press NEXT to continue. 
 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 

 
 
 
 

Valve 4 
Product Flow 
Adjustment 
Valve 

Valve 3 
Tank Fill 
Valve 

Summary of Contents for NEXGEN50







































Reviews: