background image

Programmable AC Source 61601/61602/61603/61604 Quick Start Guide 

1-2 

Table 1-1    Description of the Front Panel 

Item            Symbol 

                     Description 

 

Display

: The LCD is to display configuration, 

output setup, and    measurement results. 

           

Indicator LED

: "OUT" and "SHIFT", for showing 

activation of output and shift mode, are available 
which are located on the keypad area next to the 
corresponding keys. 

 

 

   

 

 

   

---------or-------- 

PAGE 

   

PAGE 

     

Cursor moving keys

: These two keys are to 

move the cursor to different directions 
respectively.    In normal mode, pressing any of 
these two keys will change the place of the 
cursor.    Under shift mode, these keys enable the 
LCD display to change to last page or next page if 
there are 

 or 

 patterns in right-down side of 

display. 

 

 

PAGE/EXIT 

---------or---------

SAVE 

PAGE or EXIT command key

: Pressing this 

key will make the LCD display switching 
between MAIN PAGE and CHOICE PAGE. Or 
change to CHOICE PAGE in each functional list.   
Under shift mode, pressing this key on MAIN 
PAGE, the uses can save the output setting 
(see 3.8.1 in 

Programmable AC Source 61601/ 

61602/61603/61604 User’s Manual

).  If 

pressing the key on CHOICE PAGE, the user 
can save system data (see 3.8.2 in 

Programmable AC Source 61601/61602/61603/ 
61604 User’s Manual

).  

 

Õ

 / -   

----------or---------

RECALL 

Backspace and Minus command key

Pressing this key will erase the keyin number.   
Or it may show " - ", if no number is in front of 
cursor. Under shift mode, pressing the key on 
MAIN PAGE, the user can recall the output 
setting (see 3.8.1 in 

Programmable AC Source 

61601/61602/61603/61604 User’s Manual

).  If 

pressing the key on CHOICE PAGE, the user 
can recall system data (see 3.8.2 in 

Programmable AC Source 61601/61602/61603/ 
61604 User’s Manual

).

   

 

 

OUT/QUIT  

OUT/QUIT command key

: Pressing this key may 

enable the ac source output voltage or quit the 
output voltage. 

Summary of Contents for 61601






















Reviews: