background image

                      

 

Page | 3  

 

PVT-MCT10A-EN  

What is Included  

NOTE: 

Reading through this manual is a 

necessity.  The Chromasun micro-
concentrator (MCT) High-Temperature 
Thermal Collector System requires attention 
to detail for installation. 

NOTE:

 

The installation of this equipment 

must comply with all National, State, and 
Local Codes. 

 Core System Components: 

 

Fully Assembled MCT Unit(s) 

 

Solar Field Controller(s) (SFC’s) 

 

Power, Data, Ventilation (PDV) 
Interconnects(s) 

 

Junction Box(es) 

Recommended (Optional): 

 

Sling Kit 

o

 

Four Legged Nylon Bridle 

 

Mounting Kit 

o

 

Leg Stands 

o

 

Stand Clamps 

o

 

All required Fasteners 

 

Header Kit 

o

 

Steel Header Pipes 

 

NOTE:  Any materials and work required to 
prepare the roof for the MCT must be 
provided for by the installing contractors.  

 

 

Shipping Inspection

 

As soon as the MCT arrives at the job site: 

 

Verify that all of the units have arrived 
by inspecting the shipping labels and 
comparing them to the identification 
data on the sales order and bill of lading 

 

Visually inspect the exterior of the crate 
and the visible areas of the MCTs for 
signs of shipping damage 

 

If any damage is found, the consignee 
should indicate such damage before 
signing the bill of lading and 
immediately file a claim with the carrier. 

Unit Inspection  

If, during unloading from the transport 
pallet, job site inspection reveals damage to 
an MCT, immediately file a claim with the 
carrier. Do not install any damaged parts 
without appropriate Chromasun customer 
support’s approval! 

 

Visually inspect the internal 
components for shipping damages and 
for material shortages as soon as 
possible. Concealed damage must be 
reported within 15 days 

 

If concealed damage is discovered, stop 
unpacking the shipment. If possible, 
take photos of the damage. The owner 
must provide reasonable evidence that 
the damage did not occur after delivery 

 

Notify the carrier of damage 
immediately. Request an immediate 
joint inspection of the damage with the 
carrier. Do not attempt to repair any 
parts until the damage is inspected by 
the carrier and you have received 
instructions from Chromasun customer 
service. 

 

Summary of Contents for High?Temperature Thermal Collector System











































Reviews: