manualshive.com logo in svg

Chrysler 1998 Voyager, Service Manual

The Chrysler 1998 Voyager Service Manual is a comprehensive guide that provides users with detailed information and step-by-step instructions for maintaining and repairing their vehicle. Download this manual for free from our website, and gain access to valuable knowledge to keep your Voyager running smoothly.

Share
Download
background image

ABS BRAKES OPERATION AND VEHICLE
PERFORMANCE

This ABS System represents the current state-of-

the-art in vehicle braking systems and offers the
driver increased safety and control during braking.
This is accomplished by a sophisticated system of
electrical and hydraulic components. As a result,
there are a few performance characteristics that may
at first seem different but should be considered nor-
mal. These characteristics are discussed below.

NORMAL BRAKING SYSTEM FUNCTION

Under normal braking conditions, the ABS System

functions the same as a standard brake system with
a diagonally split master cylinder and conventional
vacuum assist.

ABS SYSTEM OPERATION

If a wheel locking tendency is detected during a

brake application, the brake system will enter the
ABS mode. During ABS braking, hydraulic pressure
in the four wheel circuits is modulated to prevent
any wheel from locking. Each wheel circuit is
designed with a set of electric solenoids to allow mod-
ulation, although for vehicle stability, both rear
wheel solenoids receive the same electrical signal.

During an ABS stop, the brakes hydraulic system

is still diagonally split. However, the brake system
pressure is further split into four control channels.
During antilock operation of the vehicle’s brake sys-
tem the front wheels are controlled independently
and are on two separate control channels and the
rear wheels of the vehicle are controlled together.

The system can build and release pressure at each

wheel, depending on signals generated by the wheel
speed sensors (WSS) at each wheel and received at
the Controller Antilock Brake (CAB).

ABS operation is available at all vehicle speeds

above 3 to 5 mph. Wheel lockup may be perceived at
the very end of an ABS stop and is considered nor-
mal.

VEHICLE HANDLING PERFORMANCE DURING
ABS BRAKING

It is important to remember that an antilock brake

system does not shorten a vehicle’s stopping distance
under

all

driving

conditions,

but

does

provide

improved control of the vehicle while stopping. Vehi-
cle stopping distance is still dependent on vehicle
speed, weight, tires, road surfaces and other factors.

Though ABS provides the driver with some steer-

ing control during hard braking, there are conditions
however, where the system does not provide any ben-
efit. In particular, hydroplaning is still possible when
the tires ride on a film of water. This results in the
vehicles tires leaving the road surface rendering the
vehicle virtually uncontrollable. In addition, extreme

steering maneuvers at high speed or high speed cor-
nering beyond the limits of tire adhesion to the road
surface may cause vehicle skidding, independent of
vehicle braking. For this reason, the ABS system is
termed Antilock instead of Anti-Skid.

NOISE AND BRAKE PEDAL FEEL

During ABS braking, some brake pedal movement

may be felt. In addition, ABS braking will create
ticking, popping and/or groaning noises heard by the
driver. This is normal due to pressurized fluid being
transferred between the master cylinder and the
brakes. If ABS operation occurs during hard braking,
some pulsation may be felt in the vehicle body due to
fore and aft movement of the suspension as brake
pressures are modulated.

At the end of an ABS stop, ABS will be turned off

when the vehicle is slowed to a speed of 3–4 mph.
There may be a slight brake pedal drop anytime that
the ABS is deactivated, such as at the end of the stop
when the vehicle speed is less then 3 mph or during
an ABS stop where ABS is no longer required. These
conditions will exist when a vehicle is being stopped
on a road surface with patches of ice, loose gravel or
sand on it. Also stopping a vehicle on a bumpy road
surface will activate ABS because of the wheel hop
caused by the bumps.

TIRE NOISE AND MARKS

Although the ABS system prevents complete wheel

lock-up, some wheel slip is desired in order to
achieve optimum braking performance. Wheel slip is
defined as follows, 0 percent slip means the wheel is
rolling freely and 100 percent slip means the wheel is
fully locked. During brake pressure modulation,
wheel slip is allowed to reach up to 25 to30%. This
means that the wheel rolling velocity is 25 to 30%
less than that of a free rolling wheel at a given vehi-
cle speed. This slip may result in some tire chirping,
depending on the road surface. This sound should not
be interpreted as total wheel lock-up.

Complete wheel lock up normally leaves black tire

marks on dry pavement. The ABS System will not
leave dark black tire marks since the wheel never
reaches a fully locked condition. Tire marks may
however be noticeable as light patched marks.

START UP CYCLE

When the ignition is turned on, a popping sound

and a slight brake pedal movement may be noticed.
Additionally, when the vehicle is first driven off a
humming may be heard and/or felt by the driver at
approximately 20 to 40 kph (12 to 25 mph). The ABS
warning lamp will also be on for up to 5 seconds
after the ignition is turned on. All of these conditions
are a normal function of ABS as the system is per-
forming a diagnosis check.

5 - 86

BRAKES

NS

DESCRIPTION AND OPERATION (Continued)

Summary of Contents for 1998 Voyager



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 1998 Voyager

Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Brand: Genesis Pages: 3
Saab 92X Owner'S Manual preview
92X
Brand: Saab Pages: 445
M7 SPEED AGS-R2 Manual preview
AGS-R2
Brand: M7 SPEED Pages: 6
ACV 281178-28G-M Installation Manual preview
281178-28G-M
Brand: ACV Pages: 2
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Brand: FALCON RIDGE Pages: 5
Warn 70948 Installation Instructions preview
70948
Brand: Warn Pages: 5
cam 40103 AL Mounting Instructions preview
40103 AL
Brand: cam Pages: 6
AIS MAZMOD2 Manual preview
MAZMOD2
Brand: AIS Pages: 2
Waeco Perfect Fit MBM120 Installation Instructions preview
Perfect Fit MBM120
Brand: Waeco Pages: 3
Or-Fab HD Bumper Installation Instructions preview
HD Bumper
Brand: Or-Fab Pages: 4
Yakima K974 Manual preview
K974
Brand: Yakima Pages: 11
Toyota 2011 Camry SE V6 Brochure & Specs preview
2011 Camry SE V6
Brand: Toyota Pages: 33
Tesla Gen 3 Manual preview
Gen 3
Brand: Tesla Pages: 42
Brodit Heavy Duty ProClip Installation Instructions preview
Heavy Duty ProClip
Brand: Brodit Pages: 2
Metra Electronics 95-7322 Installation Instructions Manual preview
95-7322
Brand: Metra Electronics Pages: 16
Arctic Cat 2010 ATV 150 Service Manual preview
2010 ATV 150
Brand: Arctic Cat Pages: 101
ULTIMATE SPEED ULG 12 B3 Operation And Safety Notes preview
ULG 12 B3
Brand: ULTIMATE SPEED Pages: 56
Camcar 40072 Mounting Instructions preview
40072
Brand: Camcar Pages: 2

Brands by name

Popular brands

Load more brands