Chrysler Directed Installation Manual Download

Page: 14 / 18

Directed Digital Solutions CHRYSLER13

External module synchronization

LED

Description

Troubleshooting

(Flashes red, red,
then orange) x 10

OBDII feature not supported.

The diagnostic data bus was not detected, therefore the SmartStart features will be limited.

Active Ground When Running (Status)

LED

Description

Troubleshooting

Flashes green

Ground When Running (Status) command

received.

The module has initialized the remote start sequence.

Flashes red &
orange

Ignition ON command received.

The module has received the Ignition ON command and is processing the remote start sequence.

Flashes green
quickly

Start ON command received.

The module has received the Start ON command and is processing the remote start sequence.

Flashes red x 10

PTS shutdown error.

The PTS output from the module was not activated due to safety protection.

Flashes red x 21

CAN bus incorrectly detected.

Verify the CAN1 and CAN2 connections. Refer to "Installation (wiring diagrams, fuse selection &

vehicle wiring reference charts)" on page 8 to check the connections.

Commands

LED

Description

Troubleshooting

Flashes orange x 1

LOCK command received.

If the bypass module fails to flash, it did not receive the signal.

Commands can come from RF or D2D.

Flashes orange x 2

UNLOCK command received.

Flashes orange x 3

TRUNK command received.

Flashes orange x 4

AUX1command received.

Flashes orange x 5

AUX2 command received.

Flashes orange x 6

AUX3 command received.

Shutdown codes

LED

Description

Troubleshooting

Flashes green x 1

Takeover successful.

Normal operation.

Flashes red x 1

Runsafe was not disabled.

No UNLOCK command was received prior to opening the door, or the 45 second timer expired

in takeover mode.

Flashes red x 2

Brake was not detected.

The brakes were not detected, which prevents the system from shutting down the vehicle.

Flashes red x 3

Smart key was not detected.

The smart key was not detected, which prevents the system from shutting down the vehicle.

Flashes red x 4

Speed was detected.

The vehicle was detected as moving, which prevents the system from shutting it down.

Analog error codes

LED

Description

Troubleshooting

Flashes red, green
& orange

DEI feature error.

A feature config file mismatch was detected. Please contact Technical Support.

Summary of Contents for Directed



















Search results

Summary of Contents for Directed

Reviews:

Related manuals for Directed

Brands by name

Popular brands

Chrysler Directed, Installation Manual

Search results

Summary of Contents for Directed

Reviews:

Related manuals for Directed

Brands by name

Popular brands