background image

12

                          

Problem  

  LED display 

Alarm 

Possible cause 

Solution

The 10#  battery 

 

LED is blinks

Beep once 

every second

The charger of the 

UPS is defective

Please contact the distributor  

or Service center.

The 7#  The bypass 

indicator light

-

The Load more 

than power out 

of UPS or UPS 

internal fault

Re duce the load, please contact the  

distributor or service center

-

The 9#  The in-

verter indicator off

UPS off or UPS 

internal fault

Turn on switch "ON" UPS, please  

contact the distributor or service center

The 8#  utility 

power LED 

 

blinks in 

normal mode

-

Maybe reversed 

 

polarity (L, N) 

of site wiring or 

disconnect 

 with ground, or the 

voltage between 

neutral wiring to 

protective ground 

 

is to high

Please check the polarity of the neutral 

wiring and the line wiring, ensure that The 

green/yellow  wire  connect  protective

 

ground properly, or make sure the voltage

 

between  neutral  wiring  to  protective 

ground is less than 36VAC.

Table 6-1 UPS troubleshooting of LED panel indicator

6. Troubleshooting

                                    

In the event of an UPS fault, shoot the trouble according to Table 6-1, Table 6-2 and 6-3. If the fault still 

persists, please contact our customer service center.

Summary of Contents for Venus Smart 1K






















Reviews: