10
11
ENGLISH
CLEANING THE CATALYTIC CONVERTER
To be carried out if you suspect poor incineration or a cycle of 30 days’ use has been completed.
1. Wait for the toilet to cool down and the fan to stop.
2. Pull the toilet shell out from the rear wall. The shell will automatically move out and up with the
help of a inside lifting mechanism and remain in the service position.
3. Lift the shell completely off the lifting mechanism (Illustration 9).
4. Loosen the screw on the fan cover (Illustration 10).
5. Remove the fan cover. Loosen it from the retaining screw by turning it slightly backwards.
Then lift it out (Illustration 11).
6. Remove the catalyst pipe with the catalytic converter (Illustration 12).
7. Rinse the catalytic converter in warm water (Illustration 13).
8. Reassemble the parts in reverse order. Make sure that the catalyst pipe is put in the same position
as it was before disassembly.
9. Place the toilet chamber back onto the lifting mechanism.
10. Run a dry incineration cycle (by pressing the start button) to dry out the catalytic converter.
Illustration 9
Illustration 12
Illustration 10
Illustration 13
Illustration 11
TROUBLESHOOTING
Reset the toilet by holding the start button down for 8 seconds.
You can release the button when you hear a long beep.
Error
Red light
Yellow
light
Green light
Sound signal
Remedy
Problem with
exhaust fan.
Flashing
Flashing
10 beeps
1. Reset the toilet.
2. Open and close the toilet lid.
3. Start incineration.
4. If error recurs, contact dealer/
service.
Problem with
gas fan.
Flashing
Flashing
Flashing
10 beeps
1. Reset the toilet.
2. Open and close the toilet lid.
3. Start incineration.
4. If error recurs, contact dealer/
service.
Problem with gas
burner after 3
attempts to ignite it.
Flashing
Continuous
beeps
1. Check that the gas is connected.
2. Connect it if necessary and reset the
toilet.
3. Reset the thermal switch if needed.
4. Open and close the toilet lid.
5. Start incineration.
6. If error recurs, contact dealer/
service.
Hatch is jammed.
Flashing
10 beeps
When toilet is warm:
1. Press the start button multiple times
without inserting a new bowl liner.
2. Open the lid after each attempt. If
this does not work, wait for the toilet
to cool down (fan has stopped).
When toilet is cold:
1. Open the toilet lid and press start.
The lid opens.
2. Remove the cause of the blockage.
Ash container
is not in correct
position.
Flashing
Flashing
3 beeps
Place ash container into correct position.
Error in the
temperature
sensor
Flashing
Flashing
Continuous
Try to reset the toilet. If this does not
work, contact workshop or dealer.
Thermal switch
released.
Illuminated
Continuous
Reset thermal switch (see separate
section).
The ash container
is full. The toilet is
disabled for use.
Illuminated
Illuminated
Continuous
Empty and clean ash container.
No lights, no
sound.
Check that the caravan’s/motor home’s
main switch is on. Check that 12 V voltage
is connected.
Burnt smell
outside caravan/
motor home.
Clean catalytic converter. Ensure that the
exhaust pipe is open.
Low voltage
< 11.0 V.
Flashing
Resolve the error on the 12 V supply from
the car/caravan.
Minimum allowed
voltage < 10.5 V.
The gas supply is
shut off.
Flashing
(after 1.5 min)
10 beeps,
recurrent
Resolve the error on the 12 V supply from
the motor home/caravan.
Critically low
voltage. Immediate
shut-down.
10 beeps
Resolve the error on the 12 V supply from
the motor home/caravan.
NOTE!
Summary of Contents for Motion
Page 44: ...86 87 ESPAÑOL ...