Cirrus 3CFM Instruction Manual Download

Page: 14 / 15

interference

Troubleshooting

PROBLEM

CAUSE

REMEDY

Model will not move/

No batteries in transmitter/model

Install batteries

Battery installation is incorrect

Install batteries correctly, noting

+ & - symbols

Weak batteries in transmitter

Replace/recharge batteries

Weak batteries in model

Replace/recharge batteries

Radio interference

Relocate or change crystals

Connector disconnection

Reinsert connector(s)

Tx/Rx* crystal disconnected

Push in crystal(s)

Dirty battery contacts

Wipe clean with dry cloth

ON/OFF switch in ‘OFF’ position

Move ON/OFF switch to ‘ON’

position

ON/OFF switch is defective

Replace ON/OFF switch

No control of model

Weak batteries in transmitter

Replace/recharge batteries

Weak batteries in model

Replace/recharge batteries

Radio interference

Relocate or change crystals

Limited radio range/

Weak batteries in transmitter

Replace/recharge batteries

Weak batteries in model

Replace/recharge batteries

Transmitter aerial loose

Tighten transmitter aerial

Transmitter aerial cannot be extended

Replace transmitter aerial

Receiver aerial damaged/cut

Return receiver for repair

Motor (electric model) not suppressed

Fit motor suppressors

* Tx = Transmitter / Rx = Receiver

Please retain this information for future reference.

does not recieve a
signal

Summary of Contents for 3CFM
















Search results

Summary of Contents for 3CFM

Reviews:

Related manuals for 3CFM

Brands by name

Popular brands

Cirrus 3CFM, Instruction Manual

Search results

Summary of Contents for 3CFM

Reviews:

Related manuals for 3CFM

Brands by name

Popular brands