background image

Safety Precautions 

Thank you for purchasing this CIRRUS 3CFM computer radio control system. Before using this radio, and to ensure 
your  safety  and  that  of  others,  it  is  important  that  you  read  this  manual  thoroughly,  and  understand  it,  prior  to 

installation and operation. After reading this manual thoroughly, store it in a safe place so that you can easily find it 

again should the need arise.

Just  as  commercial  radio  stations  have  their  own  frequency  bands,  so  do  radio  control  systems.  Each  radio 
control system comes with a sticker on the transmitter and on the receiver showing which basic frequency the 
radio control system operates on (27MHz, 40MHz or 75MHz band). Each main frequency is broken down into 
various  sub-frequencies,  called  channels  (e.g.  27.045MHz,  27.145MHz,  etc.),  which  allow  multiple  models  to 
operate together without interference. In order to be able to operate on different channels the transmitter and 

receiver are fitted with removable crystals. Each crystal will have its actual frequency printed on it and details 

of whether it is for transmitter (Tx) or receiver (Rx). Crystals are matched in pairs (e.g. Tx 27.145MHz and Rx 
27.145MHz).  Transmitter  and  receiver  crystals  (matched  pairs)  can  be  purchased  separately  and  changed  if 
interference is detected (someone operating on the same frequency as you). As a rule it is always good to carry 
at least one spare pair of crystals to allow for this possibility.

Note:  The  3CFM  transmitter  has  a  location  to  store  a  spare  pair  of  crystals  located  inside  its  battery 
compartment.

Before Operation 

Should any item be missing or if you are uncertain of the contents of the system, please contact the dealer from 
whom you purchased the system before use.

27MHz and 75MHz 

These frequencies are legal for use in North America. 

27MHz and 40MHz 

These frequencies are legal for use in Europe, but can vary from country to country.

DISTRIBUTED IN NORTH 

AMERICA BY: 

Global Hobby Distributors 

18480 Bandilier Circle 

Fountain Valley, CA 92708

DISTRIBUTED IN 

EUROPE BY: 

Ripmax Ltd. 

241 Green Street 

Enfield, EN3 7SJ, U.K. 

The contents of this manual are subject to change without prior notice. 

Ref: 3CFM1

2

Spare Crystal Storage

Battery Compartment

Summary of Contents for 3CFM
















Reviews: