C I R R U S
C O M P O N E N T M A I N T E N A N C E M A N U A L - C A P S
M O D E L S R 2 0
95-01-01
Page 43
All
EFFECTIVITY:
5
Insert cable loop into firing pin actuator slot on rocket igniter and using a magnetized
screwdriver, install screw and washer to firing pin actuator slot.
WARNING:
Activation of rocket igniter requires 25 lb (11.25 kg) pull force. The
following verification is meant only to ensure firing pin capture.
A very slight pull force of 1/3 lb (0.113 kg) is all that is required to
verify capture.
6
Slightly pull cable projecting from rocket motor assembly base to verify firing pin cap-
ture.
7
Screw activation cable cone adapter to rocket cone.
8
Install access hole plug to rocket cone.
(u)
Serials 1005 thru 1267 after SB2X-95-20,
Serials 1268 thru 1422 after SB2X-95-17,
Serials 1423 & subs w/o Perspective after SB2X-95-18, 2228 & subs:
Connect activation
cable to rocket assembly.
1
Ensure firing pin actuator is rotated so threaded side of actuator is facing aft and screw
head attaching activation cable to firing pin actuator will be visible when installed.
2
Apply light threadlocker to screw used to secure activation cable to firing pin actuator.
3
Insert cable loop into firing pin actuator slot on igniter switch and using a magnetized
screwdriver, install screw and washer to firing pin actuator slot.
WARNING:
Activation of rocket igniter requires 25 lb (11.25 kg) pull force. The
following verification is meant only to ensure firing pin capture.
A very slight pull force of 1/3 lb (0.113 kg) is all that is required to
verify capture.
4
Slightly pull cable projecting from igniter switch to verify firing pin capture.
(v)
Serials 1886 & subs w/ Aircraft Data Logger
: Connect plug P1046 to jack J1046 and
secure wire harness with cable ties to existing cable anchors on rocket shield.
(w)
Serials 1005 thru 1267 after SB2X-95-20,
Serials 1268 thru 1422 after SB2X-95-17,
Serials 1423 & subs w/o Perspective after SB2X-95-18, 2228 & subs:
Connect plug P2701
to jack J2701 and secure wire harness with cable ties to existing cable anchors on rocket
shield.
(x)
Serials 1005 thru 1267 before SB2X-95-20,
1268 thru 1422 before SB2X-95-17,
Serials 1423 & subs w/o Perspective before SB2X-95-18, 2016 thru 2227:
Verify LH edge
of pick-up collar is oriented approximately 30° away from BH 222.
(y)
Serials 1005 thru 1267 after SB2X-95-20,
Serials 1268 thru 1422 after SB2X-95-17,
Serials 1423 & subs w/o Perspective after SB2X-95-18, 2228 & subs:
Verify LH edge of
pick-up collar is oriented approximately 45° away from BH 222.
(z)
Serials 1005 thru 1267 before SB2X-95-20,
1268 thru 1422 before SB2X-95-17,
Serials 1423 & subs w/o Perspective before SB2X-95-18, 2016 thru 2227:
Verify minimum
gap of 0.40 inch (10.16 mm) exists between outer diameter of pick-up collar ring and aft
side of BH 222.
(aa) Serials 1005 thru 1267 after SB2X-95-20
4 May 2015
