background image

DCC-HD3 

 

Rev. 905-0118-00 

 

©2017 CIS Corporation. All rights reserved. 

7.3.

 

<Reference> surface temperature of each device in the CIS chassis (29mm

×

29mm

×

77mm) 

 

Ambient 
temperature 

25

 

40

 

45

 

Image sensor 

58 

73 

78 

FPGA 

55.7 

70.7 

75.7 

CPU 

51.7 

66.7 

71.7 

SDI IC 

55.1 

70.1 

75.1 

 
8.

 

GenLock 

Input analog external sync signals (black burst or 3-value SYNC) to the EXT SYNC IN terminal of 6pins connector to 
enable Gen Lock function. 
The external sync signals to be supplied shall depend on its video output format, therefore, please refer to the chart 
below and input appropriate signals. 
 

 

EXT SYNC

 

IN 

CA

M

ER

A FO

R

M

AT

 

1080p60A 

 

 

 

 

1080i60 

720p60 

1080p30 

1080p59.9A 

NTSC 

 

 

1080i59.9 

720p59.9 

1080p29.9 

1080p50A 

 

 

PAL 

1080i50 

720p50 

1080p25 

1080p60B 

 

 

 

 

1080i60 

720p60 

1080p30 

1080p59.9B 

NTSC 

 

 

1080i59.9 

720p59.9 

1080p29.9 

1080p50B 

 

 

PAL 

1080i50 

720p50 

1080p25 

1080i60 

 

 

 

 

1080i60 

720p60 

1080p30 

1080i59.94 

NTSC 

 

 

1080i59.9 

720p59.9 

1080p29.9 

1080i50 

 

 

PAL 

1080i50 

720p50 

1080p25 

1080p30 

 

 

 

 

1080i60 

720p60 

1080p30 

1080p29.9 

NTSC 

 

 

1080i59.9 

720p59.9 

1080p29.9 

1080p25 

 

 

PAL 

1080i50 

720p50 

1080p25 

1080p24 

 

 

 

 

 

 

 

 

1080p24 

1080p23 

 

 

 

 

 

 

 

 

1080p23.9 

720p60 

 

 

 

 

1080i60 

720p60 

1080p30 

720p59.9 

NTSC 

 

 

1080i59.9 

720p59.9 

1080p29.9 

720p50 

 

 

PAL 

1080i50 

720p50 

1080p25 

 

Input Black Burst signals for NTSC/PAL signal. 

 

Input 3-value SYNC signals for other than NTSC/PAL signal. 

 

EXT SYNC IN is terminated with 75Ω. (It becomes high impedance when camera power is OFF). 

 

When the external signals specified above are input, the camera becomes external sync mode automatically. 

 

When no external signal is input, the camera operates in internal sync mode. 

 

The image may be disturbed right after the external signal is input, but this is not malfunction. 

 

When a signal other than specified above combination is input to the EXT SYNC IN terminal, the image might be 
disturbed or no image might be output. 

 

 

9.

 

LTC (Longitudinal Time code) 
Time code can be inserted into 3G/HD SDI signals. 
Input LTC signals (time code) to the LTC IN terminal of the 6pins connector to insert external time code. 
And, when no signal is input into the LTC IN terminal, internal time code can be inserted.     
Internal time code starts with 00:00:00. 00 when power is ON, and when any signals are input into the LTC IN terminal,   
it will be switched to the external time code. 
With this situation, if no signal is input into the LTC IN terminal, it starts self-running from the set time code. 
Signal Format: SMPTE Time code  Signal Level: 0.5 ~ 2[Vp-p] 

Summary of Contents for DCC-HD3































Reviews: