manualshive.com logo in svg

Cisco 5505 - ASA Firewall Edition Bundle, Cli Configuration Manual

The Cisco 5505 - ASA Firewall Edition Bundle is a robust network security appliance designed to protect your data and ensure secure connectivity. To get started quickly and easily, download the free "Getting Started Manual" from our 88.208.23.73:8080, offering step-by-step instructions for seamless installation and configuration.

Share
Download
background image

 

1-5

Cisco ASA Series CLI Configuration Guide

 

Chapter 1      Configuring IPv6 Neighbor Discovery

  Guidelines and Limitations

•

By default, prefixes configured as addresses on an interface using the

 ipv6 address

 command are 

advertised in router advertisements. If you configure prefixes for advertisement using the 

ipv6 nd 

prefix

 command, then only these prefixes are advertised.

•

The 

default

 keyword can be used to set default parameters for all prefixes.

•

A date can be set to specify the expiration of a prefix. The valid and preferred lifetimes are counted 
down in real time. When the expiration date is reached, the prefix will no longer be advertised.

•

When onlink is on (by default), the specified prefix is assigned to the link. Nodes sending traffic to 
such addresses that contain the specified prefix consider the destination to be locally reachable on 
the link.

•

When autoconfig is on (by default), it indicates to hosts on the local link that the specified prefix 
can be used for IPv6 autoconfiguration.

•

For stateless autoconfiguration to work correctly, the advertised prefix length in router 
advertisement messages must always be 64 bits. 

•

The router lifetime value is included in all IPv6 router advertisements sent out of the interface. The 
value indicates the usefulness of the ASA as a default router on this interface.

•

Setting the value to a non-zero value indicates that the ASA should be considered a default router 
on this interface. The non-zero value for the router lifetime value should not be less than the router 
advertisement interval.

The following guidelines and limitations apply for configuring a static IPv6 neighbor:

•

The 

ipv6 neighbor

 command is similar to the 

arp

 command. If an entry for the specified IPv6 

address already exists in the neighbor discovery cache—learned through the IPv6 neighbor 
discovery process—the entry is automatically converted to a static entry. These entries are stored in 
the configuration when the copy command is used to store the configuration.

•

Use the 

show ipv6 neighbor

 command to view static entries in the IPv6 neighbor discovery cache.

•

The 

clear ipv6 neighbor

 command deletes all entries in the IPv6 neighbor discovery cache except 

static entries. The

 no ipv6 neighbor 

command deletes a specified static entry from the neighbor 

discovery cache; the command does not remove dynamic entries—entries learned from the IPv6 
neighbor discovery process—from the cache. Disabling IPv6 on an interface by using the 

no ipv6 

enable

 command deletes all IPv6 neighbor discovery cache entries configured for that interface 

except static entries (the state of the entry changes to INCMP [Incomplete]).

•

Static entries in the IPv6 neighbor discovery cache are not modified by the neighbor discovery 
process.

•

The 

clear ipv6 neighbor

 command does not remove static entries from the IPv6 neighbor discovery 

cache; it only clears the dynamic entries. 

•

The ICMP syslogs generated are caused by a regular refresh of IPv6 neighbor entries. The ASA 
default timer for IPv6 neighbor entry is 30 seconds, so the ASA would generate ICMPv6 neighbor 
discovery and response packets about every 30 seconds. If the ASA has both failover LAN and state 
interfaces configured with IPv6 addresses, then every 30 seconds, ICMPv6 neighbor discovery and 
response packets will be generated by both ASAs for both configured and link-local IPv6 addresses. 
In addition, each packet will generate several syslogs (ICMP connection and local-host creation or 
teardown), so it may appear that constant ICMP syslogs are being generated. The refresh time for 
IPV6 neighbor entry is configurable on the regular data interface, but not configurable on the 
failover interface. However, the CPU impact for this ICMP neighbor discovery traffic is minimal.

Summary of Contents for 5505 - ASA Firewall Edition Bundle





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 5505 - ASA Firewall Edition Bundle

Juniper CTP150 Quick Start Manual preview
CTP150
Brand: Juniper Pages: 22
CommScope Q4000 Installation Instructions Manual preview
Q4000
Brand: CommScope Pages: 25
Eads Racal Instruments 1264C Manual preview
Racal Instruments 1264C
Brand: Eads Pages: 100
Advantech IPC-3026 User Manual preview
IPC-3026
Brand: Advantech Pages: 30
Advantech HPC-7484 User Manual preview
HPC-7484
Brand: Advantech Pages: 32
Aurora DXM G4 Series User Manual preview
DXM G4 Series
Brand: Aurora Pages: 57

Brands by name

Popular brands

Load more brands