manualshive.com logo in svg

Cisco ASR 5000, Administration Manual

Looking for the Installation Manual for Cisco ASR 5000? Look no further! Our website offers easy and free downloads of user manuals. Get all the information you need about Cisco ASR 5000's installation process from the comfort of your home, just visit 88.208.23.73:8080 and download it now!

Share
Download
background image

Configuring a New Chassis Key Value

CLI Commands

Only a user with Security Administrator privilege can execute the

chassis key value

and

chassis keycheck

commands.

Important

Use the Exec mode

chassis key value key_string

command to enter a new chassis key.

The

key_string

is an alphanumeric string of 1 through 16 characters. The chassis key is stored as a one-way

encrypted value, much like a password. For this reason, the chassis key value is never displayed in plain-text
form.

The Exec mode

chassis keycheck key_string

command generates a one-way encrypted key value based on

the entered

key_string

. The generated encrypted key value is compared against the encrypted key value of the

previously entered chassis key value. If the encrypted values match, the command succeeds and keycheck
passes. If the comparison fails, a message is displayed indicating that the key check has failed. If the default
chassis key (MAC address) is currently being used, this key check will always fail since there will be no
chassis key value to compare against.

Use the

chassis keycheck

command to verify whether multiple chassis share the same chassis key value.

For release 19.2 and higher, in the absence of an existing chassis ID file the

chassis keycheck

command

is hidden.

Important

For additional information, refer to the

Exec Mode Commands

chapter in the

Command Line Interface

Reference

.

Beginning with Release 15.0, the chassis ID will be generated from the chassis key using a more secure
algorithm. The resulting 44-character chassis ID will be stored in the same file.

Release 14 and Release 15 chassis IDs will be in different formats. Release 15 will recognize a Release 14
chassis ID and consider it as valid. Upgrading from 14.x to 15.0 will not require changing the chassis ID or
configuration file.

However, if the chassis key is reset in Release 15 through the Quick Setup Wizard or CLI command, a new
chassis ID will be generated in Release 15 format (44 instead of 16 characters). Release14 builds will not
recognize the 44-character chassis ID. If the chassis is subsequently downgraded to Release 14, a new
16-character chassis ID will be generated. To accommodate the old key format, you must save the configuration
file in pre-v12.2 format before the downgrade. If you attempt to load a v15 configuration file on the downgraded
chassis, StarOS will not be able to decrypt the password/secrets stored in the configuration file.

For release 19.2 and higher, in a chassis where the chassis ID file already exists nothing is changed. However,
if the chassis ID file is lost in both management cards, all existing configuration files become invalid. Entering
a new chassis key that is the same as the original value will not resolve the issue because of the new method
used to generate the chassis ID.

   ASR 5000 System Administration Guide, StarOS Release 21.1

62

System Settings

Configuring a New Chassis Key Value

Summary of Contents for ASR 5000



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 5000

H&S 24/26 Operator'S Manual preview
24/26
Brand: H&S Pages: 28
Sun Microsystems Sun Storage J4400 Replacement Manual preview
Sun Storage J4400
Brand: Sun Microsystems Pages: 21
Gigabyte GZ-FAEA41-CJB User Manual preview
GZ-FAEA41-CJB
Brand: Gigabyte Pages: 12
Multitech CommPlete CC9600 User Manual preview
CommPlete CC9600
Brand: Multitech Pages: 26
Cisco ONS 15454 DWDM Installation And Operation Manual preview
ONS 15454 DWDM
Brand: Cisco Pages: 1218
National Instruments PXI EXPRESS PXIe-1095 Calibration Procedure preview
PXI EXPRESS PXIe-1095
Brand: National Instruments Pages: 6
VIA Technologies AMOS-5000 User Manual preview
AMOS-5000
Brand: VIA Technologies Pages: 39
Contec FA-UNIT-F11BE User Manual preview
FA-UNIT-F11BE
Brand: Contec Pages: 32
BitFenix phenom mini-itx Quick Installation Manual preview
phenom mini-itx
Brand: BitFenix Pages: 18
Addonics Technologies R1825SN-2MS User Manual preview
R1825SN-2MS
Brand: Addonics Technologies Pages: 2
Comet Models LCP33 Instructions preview
LCP33
Brand: Comet Models Pages: 2

Brands by name

Popular brands

Load more brands