Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 1039 / 1138

background image

only the

clear

option is configured, the threshold values defined for the

clear

option are also used as the

set

threshold values.

Command Modes

T1 configuration

E1 configuration

Command History

Modification

Release

This command was introduced.

Release 4.1.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

This command can only be configured on full T1 or E1 channel groups; it is not supported on fractional, or
DS0 links.

The

lnm remove

command cannot be configured with the

lnm major-warning

command

—

they are mutually

exclusive.

The remove threshold values must be greater than the values configured in the

lnm minor-warning

command.

LNM supports hierarchical level alarm reporting as defined in the Telcordia (Bellcore) GR-253 standard.
Hierarchical alarm reporting means that whenever a higher alarm is asserted, the lower alarm state is suppressed.
When the high alarm is cleared, the lower alarm will re-assert if the condition still exists.

For LNM, this means that if a remove threshold is exceeded resulting in a crossed event and alarm state
reached, then a minor warning alarm state is suppressed and placed in stable state. The minor crossed event
also is removed from the bistate log. Only a single crossed event for major warnings will appear in the bistate
log for the controller. When the major warning is cleared, the minor warning alarm is asserted if the condition
still exists.

Task ID

Operation

Task ID

read, write

sonet-sdh

Examples

The following example shows how to enable link noise monitoring to signal the noise attribute to PPP for
link removal on a T1 channel group using the default values for the set and clear threshold values of 1544
LCVs and 320 PCVs for a duration of 10 seconds:

RP/0/RSP0/CPU0:router(config)#

controller t1 0/6/0/0/1/1

RP/0/RSP0/CPU0:router(config-t1)#

lnm remove

The following example shows how to specify set and clear thresholds for link noise monitoring on an E1
channel group to signal the noise attribute to PPP for link removal:

RP/0/RSP0/CPU0:router(config)#

controller e1 0/3/0/0/0/1

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1019

T3, E3, T1, E1 Controller Commands on the Cisco ASR 9000 Series Router

lnm remove

«
...
1037
1038
1039
1040
1041
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Trulink Media gateway W02

Brand: C2G Pages: 23

Brand: Wintec Pages: 14

ASLINK B2G78-PB1

Brand: Anywire Pages: 50

Flamco Flamconnect GW-10

Brand: Aalberts Pages: 2

Brand: TEKTELIC Communications Pages: 34

Brand: daviteq Pages: 14

Brand: evertz Pages: 52

AMG1312-T Series

Brand: ZyXEL Communications Pages: 300

Brand: ZyXEL Communications Pages: 307

4S Media Server

Brand: Snom Pages: 102

Provntia MX4006

Brand: IBM Pages: 2

DSL GATEWAY GT704

Brand: ActionTec Pages: 123

Brand: Arris Pages: 42

ProtoNode FPC-N34

Brand: Laars Pages: 44

Brand: 2N Telekomunikace Pages: 5

Brand: RADVision Pages: 20

Brand: Maipu Pages: 72

Brand: Harman Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands