Cisco ASR 9000 Series Command Reference Manual Download

Page: 1130 / 1138

Description

Field

Displays the following WAN Interconnect Sublayer
(WIS) layer alarms:

•

SER

—

Number of Severely Errored Frames

(SER) errors

•

FELCDP

—

Number of Far End - Loss of

Code-group Delineation - Path (FELCDP) errors

•

FEAISP

—

Number of Far End - AIS - Path

(FEAISP) errors

•

WLOS

—

Number of WIS LOS (WLOS) errors.

•

PLCD

—

Number of Path Loss of Code-group

Delineation (PLCD) errors

•

LFEBIP

—

Number of Line - Far End - BIP

(LFEBI) errors

•

PBEC

—

Number of Path - Block Error Counter

(PBEC) errors

Alarms are applicable only when the
controller is configured in WAN-PHY mode.

Note

WIS ALARMS

Total number of currently active alarms on this
interface.

Alarms are applicable only when the
controller is configured in WAN-PHY mode.

Note

Active Alarms[All defects]

Total number of the most significant active alarms
on this interface. These alarms are likely causing all
other alarms on the interface.

Alarms are applicable only when the
controller is configured in WAN-PHY mode.

Note

Active Alarms[Highest Alarms]

Total number of errored K1/K2 bytes from the Line
OverHead (LOH) of the SONET frame that were
received by this interface.

Rx(K1/K2)

Total number of errored K1/K2 bytes from the Line
OverHead (LOH) of the SONET frame that were
transmitted by this interface.

Tx(K1/K2)

Number of errored payload pointer bytes on this
interface.

S1S0

Number of errored STS identifier (C1) bytes on this
interface.

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1110

10-Gigabit Ethernet WAN PHY Controller Commandson the Cisco ASR 9000 Series Router

show controllers wanphy

«
...
1128
1129
1130
1131
1132
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands