Cisco ASR 9000 Series Command Reference Manual Download

Page: 1133 / 1138

Description

Field

Displays the following internal information for the
interface:

•

Operational Mode

—

Current operation mode

for this controller. Can be WAN mode or LAN
mode.

•

Current Alarms

—

Bit map of all currently active

alarms on this controller. Use this information
for debugging purposes.

Alarms are applicable only when the
controller is configured in WAN-PHY mode.

Note

Internal Information

The following example shows sample output from the

show controllers wanphy

command with the

alarms

keyword:

RP/0/RSP0/CPU0:router#

show controllers wanphy 0/3/4/0 alarms

Interface: wanphy0_3_4_0
Configuration Mode: WAN Mode
SECTION

LOF = 1, LOS = 1, BIP(B1) = 2912

LINE

AIS = 1, RDI = 0, FEBE = 949, BIP(B2) = 48562

PATH

AIS = 1, RDI = 0, FEBE = 0, BIP(B2) = 0
LOP = 0, NEWPTR = 0, PSE = 0, NSE = 0

WIS ALARMS

SER = 9, FELCDP = 0, FEAISP = 0
WLOS = 1, PLCD = 0
LFEBIP = 47260, PBEC = 949

Active Alarms[All defects]:
Active Alarms[Highest Alarms]:

Rx(K1/K2): N/A, Tx(K1/K2): N/A
S1S0 = N/A, C2 = N/A

PATH TRACE BUFFER
Remote IP addr: 981.761.542.321
BER thresholds: N/A
TCA thresholds: N/A

The alarm information displayed in the

show controllers wanphy interface-id alarms

command output are

described in

Table 65: show controllers wanphy Command Output Fields, on page 1107

Related Commands

Description

Command

Clears the alarms counters for a specific 10-Gigabit Ethernet
WAN PHY controller.

clear controller wanphy, on page 1096

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

1113

10-Gigabit Ethernet WAN PHY Controller Commandson the Cisco ASR 9000 Series Router

show controllers wanphy

«
...
1131
1132
1133
1134
1135
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands