Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 355 / 1138

background image

Domain fred (level 5), Service barney

ID Interface (State)

Dir MEPs/Err RD Defects AIS

----- ------------------------ --- -------- -- ------- ---

2 Gi0/1/0/0.234 (Up)

Up

3/2

Y

RPC

Table 14: show ethernet cfm local meps Field Descriptions

Configured MEP ID of the MEP.

ID

Interface that the MEP is configured under, and the
state of the interface. The states are derived from the
interface state, the Ethernet Link OAM interworking
state, and the Spanning Tree Protocol (STP) state.

The following states are reported:

•

Up

–

Interface Up, Ethernet Link OAM Up,

STP Up

•

Down

–

Interface Down or Admin Down

•

Test

–

Interface Up, Ethernet Link OAM

loopback mode

•

Blkd

–

Interface Up, Ethernet Link OAM Up,

STP Blocked

•

Otherwise, the interface state.

Interface (State)

Direction of the MEP.

Dir

Remote Defect. Y (yes) indicates that a remote defect
is detected on at least one peer MEP. In which case,
the RDI bit is set in outgoing CCM messages.
Otherwise, N (no).

RD

Total number of peer MEPs sending CCMs to the
local MEP.

MEPs

Number of peer MEPs for which at least one error
has been detected.

Err

Types of errors detected. Each error is listed as a
single character. Multiple errors are listed if they are
from the same MEP. Possible errors are listed at the
top of the display output of the command.

Defects

Alarm Indication Signal. If AIS is configured for the
service, the configured level is displayed when an
alarm is signaled. If AIS is not configured for the
service, or if no alarm is currently signaled, this field
is blank.

AIS

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

335

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet cfm local meps

«
...
353
354
355
356
357
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Pathport Pages: 3

Brand: Billion Pages: 35

Brand: Media5 Pages: 54

SmartNode 4940 Series

Brand: Patton Pages: 59

UNIGATE MB EtherCAT

Brand: DEUTSCHMANN AUTOMATION Pages: 60

Brand: HID Pages: 38

NI WSN C Series

Brand: National Instruments Pages: 16

Brand: Aaeon Pages: 29

Brand: Gree Pages: 67

Brand: Asus Pages: 21

Brand: Asus Pages: 42

Brand: Asus Pages: 53

Aaeon UPC-GWS01

Brand: Asus Pages: 21

Brand: Asus Pages: 160

Brand: Asus Pages: 38

Brand: Asus Pages: 52

Brand: Siemens Pages: 12

Brand: Popp Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands