Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 362 / 1138

background image

This example shows sample detailed output of MEPs detected by a local MEP:

RP/0/RSP0/CPU0:router#

show ethernet cfm peer meps detail

Domain dom3 (level 5), Service ser3
Down MEP on GigabitEthernet0/0/0/0 MEP-ID 1
================================================================================
Peer MEP-ID 10, MAC 0001.0203.0403

CFM state: Wrong level, for 00:01:34
Port state: Up
CCM defects detected:

V - Wrong Level

CCMs received: 5

Out-of-sequence:

0

Remote Defect received:

5

Wrong Level:

0

Cross-connect (wrong MAID):

0

Wrong Interval:

5

Loop (our MAC received):

0

Config (our ID received):

0

Last CCM received

Level: 4, Version: 0, Interval: 1min
Sequence number: 5, MEP-ID: 10
MAID: String: dom3, String: ser3
Port status: Up, Interface status: Up

Domain dom4 (level 2), Service ser4
Down MEP on GigabitEthernet0/0/0/0 MEP-ID 1
================================================================================
Peer MEP-ID 20, MAC 0001.0203.0402

CFM state: Ok, for 00:00:04
Received CCM handling offloaded to software
Port state: Up
CCMs received: 7

Out-of-sequence:

1

Remote Defect received:

0

Wrong Level:

0

Cross-connect (wrong MAID):

0

Wrong Interval:

0

Loop (our MAC received):

0

Config (our ID received):

0

Last CCM received

Level: 2, Version: 0, Interval: 10s
Sequence number: 1, MEP-ID: 20
MAID: String: dom4, String: ser4
Chassis ID: Local: ios; Management address: 'Not specified'
Port status: Up, Interface status: Up

Peer MEP-ID 21, MAC 0001.0203.0403

CFM state: Ok, for 00:00:05
Port state: Up
CCMs received: 6

Out-of-sequence:

0

Remote Defect received:

0

Wrong Level:

0

Cross-connect (wrong MAID):

0

Wrong Interval:

0

Loop (our MAC received):

0

Config (our ID received):

0

Last CCM received 00:00:05 ago:

Level: 2, Version: 0, Interval: 10s
Sequence number: 1, MEP-ID: 21
MAID: String: dom4, String: ser4
Port status: Up, Interface status: Up

Domain dom5 (level 2), Service ser5
Up MEP on Standby Bundle-Ether 1 MEP-ID 1
================================================================================
Peer MEP-ID 600, MAC 0001.0203.0401

CFM state: Ok (Standby), for 00:00:08, RDI received
Port state: Down

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

342

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet cfm peer meps

«
...
360
361
362
363
364
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: WAGO Pages: 76

Brand: Pace Pages: 36

Intesis Modbus Server

Brand: HMS Pages: 30

Brand: Dinstar Pages: 100

Brand: RTA Pages: 43

Brand: Arris Pages: 2

Brand: Asus Pages: 21

Brand: Asus Pages: 42

Brand: Asus Pages: 53

Aaeon UPC-GWS01

Brand: Asus Pages: 21

Brand: Asus Pages: 160

Brand: Asus Pages: 38

Brand: Asus Pages: 52

Brand: ECKELMANN Pages: 34

Brand: Tadiran Telecom Pages: 89

Brand: t.a.c. Pages: 4

Brand: NETGEAR Pages: 2

Brand: NETGEAR Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands