Cisco ASR 9000 Series Command Reference Manual Download

Page: 377 / 1138

Configuration: Status counter 4, Polling Verification Timer 15 seconds
Last Data Instance Sent: 1732
Last Sequence Numbers: Sent 128, Received 128

Reliability Errors:

Status Enq Timeouts

19 Invalid Sequence Number

Invalid Report Type

Protocol Errors:

Malformed PDUs

0 Invalid Protocol Version

Invalid Message Type

0 Out of Sequence IE

Duplicated IE

0 Mandatory IE Missing

Invalid Mandatory IE

0 Invalid non-Mandatory IE

Unrecognized IE

0 Unexpected IE

Full Status Enq Rcvd

00:00:10 ago

Full Status Sent

00:00:10 ago

PDU Rcvd

00:00:00 ago

PDU Sent

00:00:00 ago

LMI Link Status Changed

10:00:00 ago

Last Protocol Error

never

Counters cleared

never

Table 18: show ethernet lmi interfaces Field Descriptions

Description

Field

Name of the interface running the E-LMI protocol.

Interface:

Status of the E-LMI protocol on the interface. Possible
values are Up, Down, or Unknown (PVT disabled).

Ether LMI Link Status:

Name of the UNI as configured by the

ethernet uni

command. This output field does not appear if the

UNI ID is not configured.

UNI Id:

Status of the interface line protocol. Possible values
are Up, Down, or Admin-Down.

Line Protocol State:

Maximum Transmission Unit of the interface and the
number (

) of E-LMI PDUs of that size required to

send one full status report.

MTU (

PDUs reqd for full report)

Map type, which describes how CE VLAN IDs are
mapped to specific EVCs. Possible valued for

type

are Bundling, All to One Bundling, or Service
Multiplexing with no bundling. The number

EVCs in the map are displayed in parentheses.

CE-VLAN/EVC Map Type:

type

(

EVCs)

Value of the MEF N393 Status Counter as configured
by the

status-counter

command.

Configuration: Status counter

Value of the MEF T392 Polling Verification Timer
(in seconds) as configured by the

polling-verification-timer

command. Displays

"disabled" if the PVT is turned off.

Polling Verification Timer

Current value of the Data Instance.

Last Data Instance Sent:

Values of the last sent (

) and received (

) sequence

numbers as reported in sent PDUs.

Last Sequence Numbers: Sent

, Received

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

357

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet lmi interfaces

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands