Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 38 / 1138

background image

Configuring two ends of an OTN link with different FEC modes is not supported. Even if different FEC modes
are configured, the FEC mismatch alarm will not be raised. Interface may experience continuous port flap in
addition to continuous bit interleaved parity (BIP) errors at both OTN and LAN level.

Task ID

Operations

Task ID

read, write

dwdm

Examples

The following example shows how to disable OTU reporting for IAE:

RP/0/RSP0/CPU0:router(config)#

controller dwdm 0/0/0/0

RP/0/RSP0/CPU0:router(config-dwdm)#

g709 otu report iae disable

Related Commands

Description

Command

Displays optical parameters, G.709 alarms and counters, and register
and module information for a DWDM controller.

show controller dwdm, on page 56

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

18

Dense Wavelength Division Multiplexing Commands on the Cisco ASR 9000 Series Router

g709 otu report disable

«
...
36
37
38
39
40
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Yeastar Technology Pages: 14

Brand: WAGO Pages: 110

Brand: THOMSON Pages: 974

Brand: Sangoma Pages: 4

KonNad C2000-D2-DCTZ02

Brand: SinoCon Pages: 11

Brand: Media Pages: 8

Brand: HD Pages: 2

VoiceGATE 8D5499

Brand: Digicom Pages: 29

Brand: BossPac Pages: 27

Brand: Xantrex Pages: 80

Brand: Juniper Pages: 26

Brand: Planet Networking & Communication Pages: 12

Brand: Planet Networking & Communication Pages: 13

Brand: ADT Pulse Pages: 6

Brand: Telecom FM Pages: 7

Brand: Teltonika Pages: 6

Brand: SmartRG Pages: 8

Brand: EnGenius Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands