Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 382 / 1138

background image

Description

Field

The OAM protocol from which the EVC status and
type are derived. Possible values are either "CFM"
or "None."

OAM Protocol:

Name of the CFM domain for this EVC.

CFM Domain:

Name of the CFM service for this EVC.

CFM Service:

Number of configured or expected remote UNIs (

x

)

and the number of active remote UNIs (

y

) within the

EVC.

Remote UNI Count: Configured =

x

, Active =

y

ID of each remote UNI, including both configured
and active remote UNIs where these two sets are not
identical. If the number of configured and active
remote UNIs is zero, no table is displayed.

Where no ID is configured for a remote UNI
using the

ethernet uni id

command, then

the CFM remote MEP ID is displayed, for
example, "<Remote UNI Reference Id:

x

>"

Note

Remote UNI Id:

Status of each remote UNI, with the following
possible values: "Up," "Down," "Admin Down,"
"Unreachable (a configured remote UNI is not active
or missing)," or "Unknown (a remote UNI is active
but not reporting its status)."

Status

Related Commands

Description

Command

Clears Ethernet LMI statistics on one or all interfaces.

clear ethernet lmi interfaces, on page 175

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

362

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet lmi interfaces

«
...
380
381
382
383
384
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

TS7650G PROTECTIER DEDUPLICATION GATEWAY

Brand: IBM Pages: 11

Brand: Sangoma Pages: 4

Brand: Ingics Pages: 12

Brand: ANTIFERENCE Pages: 26

Brand: XLOCK Pages: 2

Brand: IBM Pages: 58

MiBoxer ZB-Box2

Brand: Mi-Light Pages: 6

NetLinx Clear Connect NXB-CCG

Brand: AMX Pages: 3

NetLinx NXB-KNX

Brand: AMX Pages: 2

Brand: Wildix Pages: 4

Brand: 2Wire Pages: 4

Brand: ActionTec Pages: 83

Brand: IBM Pages: 2

Brand: IBM Pages: 20

Brand: IBM Pages: 1066

SURFboard SBG6700-AC

Brand: Arris Pages: 86

Brand: M-system Pages: 68

Brand: Zte Pages: 112

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands