Cisco ASR 9000 Series Command Reference Manual Download

Page: 384 / 1138

Each row in the table corresponds to a loopback session which is currently active. For each session, these
fields are displayed:

•

Interface: The interface on which the loopback session is running.

•

ID: The session ID allocated to the session when it was started.

•

Direction: The direction of the loopback session.

•

Time left: The amount of time left until the loopback session is automatically stopped.

•

Status: The status of the loopback session.

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

364

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet loopback active

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands