Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 395 / 1138

background image

EFD triggered: Yes (link-fault)

Table 21: show ethernet oam interfaces Field Descriptions

Description

Field

The possible discovery state

type

values are:

•

ACTIVE_SEND_LOCAL

—

The interface is

configured in active mode (the default), but no
Information PDUs have been received from the
peer (except possibly link-fault PDUs).
Information PDUs are sent.

•

FAULT

—

A local unidirectional link fault has

been detected. Link-fault PDUs are sent.

•

INACTIVE

—

The interface is down.

•

PASSIVE_WAIT

—

The interface is configured

in passive mode (

mode passive

command) but

no Information PDUs have been received from
the peer (except possibly link-fault PDUs). No
PDUs are sent.

•

REMOTE

—

(Also known as

SEND_LOCAL_REMOTE). Information PDUs
are being sent and received, but the local device
is not satisfied with the remote peer's
capabilities (for example, because there is a
'require-remote' configuration and the peer does
not have the required capabilities).

•

REMOTE_OK

—

(Also known as

SEND_LOCAL_REMOTE_OK). Information
PDUs are being sent and received, and the local
device is satisfied with the peer's capabilities,
but the remote peer is not satisfied with the local
device capabilities (for example, because there
is a 'require-remote' configuration on the peer
device).

•

SEND_ANY

—

The discovery process has

completed, both devices are satisfied with the
configuration and the session is up. All types of
PDU can be sent and received.

In

type

state

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

375

Ethernet OAM Commands on the Cisco ASR 9000 Series Router

show ethernet oam interfaces

«
...
393
394
395
396
397
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: JBM electronics Pages: 20

Brand: NetLink Pages: 68

Brand: Moxa Technologies Pages: 6

ServiceRouter V3

Brand: Eurogard Pages: 4

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 19

Brand: NKE Pages: 14

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 134

Brand: Realm Pages: 8

Brand: ICP DAS USA Pages: 48

Brand: Planet Pages: 62

Brand: Wildix Pages: 5

Brand: Wildix Pages: 15

Brand: ZyXEL Communications Pages: 35

Brand: Watchguard Pages: 18

Brand: Equustek Pages: 42

Brand: Bryan Boilers Pages: 56

MiniHub Pro WLRRTES-102 TBMH110

Brand: Browan Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands