manualshive.com logo in svg

Cisco ASR 9000 Series, Command Reference Manual

The Cisco ASR 9000 Series is a cutting-edge networking solution, offering unmatched performance and reliability. To streamline the installation process, it comes with a comprehensive Installation Manual available for free download from our website, empowering users with step-by-step instructions to maximize the potential of this exceptional product.

Share
Download
background image

frame-relay multilink retry

To configure the retry count for retransmissions for a Frame Relay multilink bundle link, use the

frame-relay

multilink retry

command in interface configuration mode. To reset the name to the default, use the

no

form

of this command.

frame-relay multilink retry retry-count

no frame-relay multilink retry

Syntax Description

Retry count for retransmissions. The range is from 1 to 5.

retry-count

Command Default

The default retry count for retransmissions is 2.

Command Modes

Interface configuration

Command History

Modification

Release

This command was introduced.

Release 4.0.0

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

frame-relay multilink retry

command is supported only on serial interfaces. The

frame-relay

multilink retry

command is not supported on Packet-over-SONET/SDH (POS) or multilink frame relay

interfaces.

Note

The

frame-relay multilink retry

command can be configured only on bundle link interfaces that have been

associated with a bundle using the

encapsulation frame-relay mfr

command.

You can enter the

frame-relay multilink retry

command at any time without affecting the current state

of the interface; however, the configured retry count value does not go into effect until the interface has
gone from the down state to the up state. One way to bring the interface down and back up again is by
using the

shutdown

and

no shutdown

commands in interface configuration mode.

Note

   Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

458

Frame Relay Commands on the Cisco ASR 9000 Series Router

frame-relay multilink retry

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

CHERUBINI METAHome Instructions Manual preview
METAHome
Brand: CHERUBINI Pages: 16
F-SECURE MESSAGING SECURITY GATEWAY - Installation Manual preview
MESSAGING SECURITY GATEWAY -
Brand: F-SECURE Pages: 19
hilscher EU5C-SWD-ETHERCAT User Manual preview
EU5C-SWD-ETHERCAT
Brand: hilscher Pages: 98
Leviton 10/100Mbps 4-Port Internet Gateway Instructions Manual preview
10/100Mbps 4-Port Internet Gateway
Brand: Leviton Pages: 10
QEI ePAQ-942 Series User Manual preview
ePAQ-942 Series
Brand: QEI Pages: 42
Advantech EDG-4508+ User Manual preview
EDG-4508+
Brand: Advantech Pages: 82
Moxa Technologies AIG-501-T-AZU-LX Quick Installation Manual preview
AIG-501-T-AZU-LX
Brand: Moxa Technologies Pages: 8
Ubee DVW32CB Installation Manual preview
DVW32CB
Brand: Ubee Pages: 7
ZyXEL Communications P-661HW-D Series Support Note preview
P-661HW-D Series
Brand: ZyXEL Communications Pages: 146
turck BL67-GW-EN How-To preview
BL67-GW-EN
Brand: turck Pages: 11
Cisco D-PCG1000 PowerKEY CAS Datasheet preview
D-PCG1000 PowerKEY CAS
Brand: Cisco Pages: 4
Solidtronic RT-RoIP2-Azetti User Manual preview
RT-RoIP2-Azetti
Brand: Solidtronic Pages: 8
Solidtronic RT-RoIP2-Zello User Manual preview
RT-RoIP2-Zello
Brand: Solidtronic Pages: 8
tiko Energy Solutions GM-01.0005R06 User Manual preview
GM-01.0005R06
Brand: tiko Energy Solutions Pages: 40
Comtrol IO-Link Master 4-EIP Initial Installation And Configuration preview
IO-Link Master 4-EIP
Brand: Comtrol Pages: 14
Vbox Communications XTi 4134 Full User Manual preview
XTi 4134
Brand: Vbox Communications Pages: 88
R9 Technology G200 User Manual preview
G200
Brand: R9 Technology Pages: 15
Watchguard SSL 560 Hardware Manual preview
SSL 560
Brand: Watchguard Pages: 26

Brands by name

Popular brands

Load more brands