Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 507 / 1138

background image

Usage Guidelines

To use this command, you must be in a user group associated with a task group that includes appropriate task
IDs. If the user group assignment is preventing you from using a command, contact your AAA administrator
for assistance.

The

show interfaces

(Frame Relay) command is available on Packet-over-SONET/SDH (POS), serial, and

multilink interfaces.

Task ID

Operations

Task ID

read, write

fr

Examples

The following example shows the output from the

show interfaces

command when the interface is configured

with Frame Relay encapsulation:

RP/0/RSP0/CPU0:router#

show interfaces pos 0/1/0/0

POS0/1/0/0 is up, line protocol is up

Hardware is Packet over SONET/SDH
Internet address is Unknown
MTU 4474 bytes, BW 622080 Kbit

reliability 255/255, txload 1/255, rxload 1/255

Encapsulation FRAME-RELAY, crc 32, controller loopback not set,
LMI enq sent

0, LMI stat recvd 0, LMI upd recvd 0

LMI enq recvd 9463, LMI stat sent

9463, LMI upd sent

0, DCE LMI up

LMI DLCI 0

LMI type is ANSI Annex D

frame relay DCE

Last clearing of "show interface" counters never
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec

20934 packets input, 1508069 bytes, 1151 total input drops
0 drops for unrecognized upper-level protocol
Received 0 broadcast packets, 0 multicast packets

0 runts, 0 giants, 0 throttles, 0 parity

1151 input errors, 1058 CRC, 0 frame, 0 overrun, 93 ignored, 0 abort
19590 packets output, 990924 bytes, 0 total output drops
Output 0 broadcast packets, 0 multicast packets
0 output errors, 0 underruns, 0 applique, 0 resets
0 output buffer failures, 0 output buffers swapped out

Table 26: show interfaces Field Descriptions

Description

Field

Displays the name of the current interface. In the
example, the interface name is POS0/1/0/0.

Interface name

Displays the state of the interface. In the example,
the interface is in the administratively up state.

Interface state

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

487

Frame Relay Commands on the Cisco ASR 9000 Series Router

show interfaces (frame relay)

«
...
505
506
507
508
509
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: VBOX Pages: 3

Brand: ISYGLT Pages: 7

WILOW-IOT-GATEWAY-4G

Brand: BEANAIR Pages: 29

AIG-501-T-AZU-LX

Brand: Moxa Technologies Pages: 8

CONTROLS Series

Brand: Condair Pages: 16

Brand: Cisco Pages: 146

Brand: Cisco Pages: 88

Brand: Cisco Pages: 108

Brand: Cisco Pages: 104

Brand: Technicolor - Thomson Pages: 21

Brand: Zoom Pages: 2

Brand: Gigaset Pages: 8

Brand: Clearswift Pages: 21

Brand: SignaMax Pages: 54

Brand: Deco Pages: 22

Brand: Speed Touch Pages: 84

1-Wire Gateway 20 Modbus TCP

Brand: esera automation Pages: 10

Brand: 3Com Pages: 306

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands