Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 509 / 1138

background image

Description

Field

Indicates that the hardware was configured as
controller loopback.

controller loopback

Number of LMI enquiry messages sent.

LMI enq sent

Number of LMI status messages received.

LMI stat recvd

Number of LMI updated messages received.

LMI upd recvd

Number of LMI enquiry messages received.

LMI enq recvd

Number of LMI status messages sent.

LMI stat sent

Number of LMI updated messages sent.

LMI upd sent

Displays the state of the DCE LMI.

DCE LMI

Displays the LMI DLCI identifier.

LMI DLCI

Displays the LMI type.

LMI type

Time at which the counters that measure cumulative
statistics (such as number of bytes transmitted and
received) shown in this report were last reset to zero.
Note that variables that might affect routing for
example, load and reliability) are not cleared when
the counters are cleared.

Last clearing

Average number of bits and packets transmitted per
second in the last 5 minutes.

The 5-minute input and output rates should be used
only as an approximation of traffic per second during
a given 5-minute period. These rates are exponentially
weighted averages with a time constant of 5 minutes.
A period of four time constants must pass before the
average is within two percent of the instantaneous
rate of a uniform stream of traffic over that period.

5 minute input rate5 minute output rate

Total number of error-free packets received by the
system.

packets input

Total number of bytes, including data and MAC
encapsulation, in the error-free packets received by
the system.

bytes

Total number of broadcast or multicast packets
received by the interface

Received...broadcasts

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

489

Frame Relay Commands on the Cisco ASR 9000 Series Router

show interfaces (frame relay)

«
...
507
508
509
510
511
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: FACTBIRD Pages: 2

Brand: Ubiquiti Pages: 19

StorNext G300 R520

Brand: Quantum Pages: 52

Brand: Inovonics Pages: 13

Brand: Eelectron Pages: 9

Brand: Hybertone Pages: 48

Brand: Agilent Technologies Pages: 111

Brand: Altice Labs Pages: 56

Brand: Cooper Controls Pages: 8

Brand: Ubiquiti Pages: 28

Brand: Ubiquiti Pages: 24

Brand: CAME Pages: 64

Sure Cross Performance GatewayPro DX80P*A6...

Brand: Banner Pages: 105

Pathport PWPP HH P1 XLR5F

Brand: pathway Pages: 62

IMG-W6121+-3G-M12

Brand: ORiNG Pages: 2

Brand: D-Link Pages: 69

Brand: Honeywell Pages: 8

Brand: VegaStream Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands