Cisco ASR 9000 Series Command Reference Manual Download

Page: 543 / 1138

Description

Field

Indicates the traffic flowing out of
the interface as a proportion of the
bandwidth.

The txload is shown as a
fraction of 255.

Note

txload

Indicates the traffic flowing into
the interface as a proportion of the
bandwidth.

The rxload is shown as a
fraction of 255.

Note

rxload

Layer 2 encapsulation installed on
the interface.

Encapsulation

Indicates the length of the cyclic
redundancy check (CRC), in bytes.

The CRC is not present
for all interface types.

Note

Enter the

pos crc

command to configure the
CRC.

Note

CRC

Indicates whether the hardware has
been configured to be looped back.

Enter the

loopback

command to configure the
loopback or controller
loopback.

Note

loopback or controller loopback

Displays the configured keepalive
value, in seconds.

Enter the

keepalive

command to configure the
value of the keepalive
field.

Note

The

keepalive

field may

not be present if it is not
applicable to the interface
type.

Note

keepalive

Displays the duplexity of the link.

This field is present only
for shared media.

Note

For some interface types,
you can configure the
duplexity by entering the

full-duplex

and

half-duplex

commands.

Note

Duplexity

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

523

Global Interface Commandsonthe Cisco ASR 9000 Series Router

show interfaces

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands