Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 546 / 1138

background image

Description

Field

Average number of bits and
packets transmitted per second in
the last 5 minutes. If the interface
is not in promiscuous mode, it
senses network traffic that it sends
and receives (rather than all
network traffic).

The 5-minute period
referenced in the
command output is a load
interval that is
configurable under the
interface. The default
value is 5 minutes.

Note

The 5-minute output
should be used only as an
approximation of traffic
per second during a given
5-minute period. This rate
is exponentially weighted
average with a time
constant of 5 minutes. A
period of four time
constants must pass before
the average will be within
two percent of the
instantaneous rate of a
uniform stream of traffic
over that period.

Note

5 minute output rate

Number of packets received on the
interface that were successfully
delivered to higher layers.

packets input

Total number of bytes successfully
received on the interface.

bytes input

Total number of packets that were
dropped after they were received.
This includes packets that were
dropped due to configured quality
of service (QoS) or access control
list (ACL) policies. This does not
include drops due to unknown
Layer 3 protocol.

total input drops

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

526

Global Interface Commandsonthe Cisco ASR 9000 Series Router

show interfaces

«
...
544
545
546
547
548
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Iget Pages: 8

Brand: 3onedata Pages: 44

Intesis Modbus Server

Brand: HMS Pages: 30

Brand: OleumTech Pages: 104

Brand: Pathway connectivity solutions Pages: 14

Brand: Pace Pages: 19

Brand: Sigma Designs Pages: 36

fieldserver EZ Series

Brand: MSA Pages: 61

SureCross DX80G9M6S0P0V4V4C

Brand: Banner Pages: 8

Brand: Kaon Pages: 12

Brand: UfiSpace Pages: 27

Brand: VBOX Pages: 11

Brand: Fluke Pages: 20

Brand: Alarm Lock Pages: 8

Brand: Alarm Lock Pages: 8

SentryPlus Alert

Brand: Watts Pages: 16

Brand: ViewSonic Pages: 48

Sentrius RG191+LTE

Brand: Laird Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands