Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 549 / 1138

background image

Description

Field

Number of underrun errors
experienced by the interface.
Underruns represent the number of
times that the hardware is unable
to transmit data to a hardware
buffer because the output rate
exceeds the transmitter

’

s ability to

handle the data.

underruns

Number of applique errors.

applique

Number of times that the hardware
has been reset. The triggers and
effects of this event are
hardware-specifc.

resets

Number of times that a packet was
not output from the output hold
queue because of a shortage of
MEMD shared memory.

output buffer failures

Number of packets stored in main
memory when the output queue is
full; swapping buffers to main
memory prevents packets from
being dropped when output is
congested. The number is high
when traffic is bursty.

output buffers swapped out

Number of times the carrier detect
(CD) signal of a serial interface has
changed state.

carrier transitions

Related Commands

Description

Command

Displays information that is specific to the interface
hardware statistics for all interfaces configured on
the networking device.

show controller interface

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

529

Global Interface Commandsonthe Cisco ASR 9000 Series Router

show interfaces

«
...
547
548
549
550
551
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

WAGO 750-8212/000-100

Brand: Viessmann Pages: 36

10/100Mbps 4-Port Internet Gateway

Brand: Leviton Pages: 10

Brand: Digi Pages: 6

Brand: Exsys Pages: 27

Brand: HID Pages: 38

Brand: LifeShield Pages: 2

Brand: Ingics Pages: 12

VBG-PN-K20-DMD-EV

Brand: Pepperl+Fuchs Pages: 11

Brand: Aaeon Pages: 26

Brand: ABB Pages: 22

Brand: Toro Pages: 40

Brand: Allied Telesis Pages: 3

Brand: Zoom Pages: 2

Brand: CPS Pages: 23

Brand: ICP DAS USA Pages: 48

Brand: Technicolor Pages: 19

Brand: evertz Pages: 52

Brand: Eelectron Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands