Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 588 / 1138

background image

•

Which members are used for a specified source/destination address pair, such as 10.10.10.1 20.20.20.1

•

The destination IP address for a specified source IP address on a specified member.

•

The load balancing distribution

–

how many times the members of a bundle are used for a specified range

of IP addresses.

The

bundle-hash

command does not display all possible IP addresses in an entire series. It stops displaying

addresses after all the addresses for all the members of the bundle have been displayed once.

The

bundle-hash

command is not applicable to multicast traffic and only applicable to unicast traffic.

The

bundle-hash

command invokes a utility that initially prompts you to select some options. Based on the

options you select, the utility prompts you more options to select. The initial options to select are as follows:

•

L3/3-tuple or L4/7-tuple

•

Single pair or Range

•

IPv4 or IPv6

The

bundle-hash

command utility prompts you for these options as follows:

•

Specify load-balance configuration (L3/3-tuple or L4/7-tuple) (L3,L4):

•

Single SA/DA pair (IPv4,IPv6) or range (IPv4 only): S/R [S]:

•

Enter bundle type IP V4 (1) or IP V6 (2):

•

Enter source IP V4 address:

•

Enter destination IP V4 address:

•

Compute destination address set for all members? [y/n]:

•

Enter subnet prefix for destination address set:

•

Enter bundle IP V4 address [10.10.10.10]:

You may also be prompted to make further option choices depending on your selections.

You can use the

show bundle

command to get IP address information.

Table 38: bundle-hash Command Options, on page 568

provides a general summary of the options and the

information you need to provide for each selected option. The actual information that you need to provide
depends on the selections you make and may vary from the information provided in

Table 38: bundle-hash

Command Options, on page 568

.

Table 38: bundle-hash Command Options

Information You Need to Provide

Option

L3 information:

•

Source IP address

•

Destination IP address

•

Destination subnet prefix

•

Bundle IP address

L3/3-tuple

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

568

Link Bundling Commands on the Cisco ASR 9000 Series Router

bundle-hash

«
...
586
587
588
589
590
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Elvaco Pages: 2

SBO500 SBO Series

Brand: Synway Pages: 72

Brand: Telco Systems Pages: 30

NETcon D-G-64NE

Brand: ZIEHL-ABEGG Pages: 27

Brand: WePresent Pages: 39

Brand: Media Pages: 8

Ixxat SG-gateway

Brand: HMS Pages: 14

Brand: gefran Pages: 2

Brand: ActionTec Pages: 2

Brand: Vantron Pages: 98

Brand: SAGEMCOM Pages: 29

Brand: Optimus Pages: 44

Brand: GL-INET Pages: 2

Brand: ACT'L Pages: 38

Brand: RTA Pages: 58

Brand: IAI Pages: 5

Brand: hager Pages: 4

PLUS+1 Connect CS100

Brand: Danfoss Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands