Cisco ASR 9000 Series Command Reference Manual Download | Manualshive

Page: 654 / 1138

background image

Description

Reason

The link is in Configured state because the System
ID or Operational Key specified by the LACP partner
device does not match that seen on other Selected
links within the same bundle. This probably indicates
a misconfiguration.

Partner System ID/Key do not match that of the
Selected links

The link is in Configured state because the
Wait-While timer is still running and the new state
has not yet been determined.

Wait-while timer is running

Related Commands

Description

Command

Specifies or creates a new bundle and enters interface configuration
mode for that bundle.

interface (bundle), on page 590

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

634

Link Bundling Commands on the Cisco ASR 9000 Series Router

show bundle

«
...
652
653
654
655
656
...
»

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ASR 9000 Series

Brand: Billion Pages: 35

Brand: TIS Pages: 5

EKI-1200-CE Series

Brand: Advantech Pages: 67

460PBSDFM-N70PB

Brand: RTA Pages: 73

Brand: ZyXEL Communications Pages: 2

Brand: AudioCodes Pages: 70

Brand: ViewSonic Pages: 57

Brand: Zoom Pages: 2

Brand: ECKELMANN Pages: 58

Brand: Bpt Pages: 25

Fieldgate SFG500

Brand: Endress+Hauser Pages: 52

Brand: Planet Networking & Communication Pages: 19

Brand: ZyXEL Communications Pages: 2

Brand: 2Wire Pages: 132

Brand: EnOcean Pages: 4

Brand: YX Pages: 51

Brand: YX Pages: 54

Brand: DLG Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands