Cisco ASR 9000 Series Command Reference Manual Download

Page: 675 / 1138

Key: 0x0001, Port priority: 32768, Port ID:

State:

Act

(T/o)

Agg

(Sync) (Coll) (Dist)

Def

(Exp)

TLV: 0x02 - Partner Information

Length:

System: Priority: 65535, ID: 00-00-00-00-00-00
Key: 0x0000, Port priority: 65535, Port ID:

State: (Act) (T/o) (Agg) (Sync) (Coll) (Dist)

Def

(Exp)

TLV: 0x03 - Collector Information

Length:

Max delay: 65535

TLV: 0x00 - Terminator

Length:

Related Commands

Description

Command

Displays the LACP transmission information that used by the
transmitting device for sending packets on an interface.

show lacp io, on page 650

Enables a short period time interval for the transmission and reception
of LACP packets.

lacp period short, on page 602

Captures LACP packets so that their information can be displayed.

lacp packet-capture, on page 599

Cisco ASR 9000 Series Aggregation Services Router Interface and Hardware Component Command Reference,

Release 5.3.x

655

Link Bundling Commands on the Cisco ASR 9000 Series Router

show lacp packet-capture

Summary of Contents for ASR 9000 Series



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands

Cisco ASR 9000 Series, Command Reference Manual

Search results

Summary of Contents for ASR 9000 Series

Reviews:

Related manuals for ASR 9000 Series

Brands by name

Popular brands